lkml.org 
[lkml]   [2021]   [Oct]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [BUG 5/5] [BUG] media: atomisp: atomisp causes touchscreen to stop working on Microsoft Surface 3
From
Date
On Sun, 2021-10-24 at 10:32 +0200, Hans de Goede wrote:
> Hi,
>
> [...]
>
> <note going a bit offtopic from atomisp here>
>
> Friday I've resized the Android data partition on my Mi Pad 2 Android,
> 16G eMMC model and installed Fedora 35 in the free space.
>
> And yesterday I've been poking at the Mi Pad 2 the entire day,
> both under Fedora and under the original Android install to figure
> out which chips there are and how they are used, etc. This has
> diverted me from looking into atomisp2 stuff, but it was fun :)
>
> I've also managed to make the i915 driver work. It still gives one
> warning during boot which I need to look into. But it works now.
> ATM my i915 fix is just a hack. I plan to turn it into something
> which I hope I can get upstream, I'll Cc you (Tsuchiya) on the
> upstream submission of the i915 submission.

Thank you! I just tried your patch and now mipad2 can boot with GPU!
So, I tried if I can reproduce touchscreen issue with atomisp, but
there was no such issue. Touchscreen works regardless of atomisp drivers.
I guess this is maybe a PMIC difference (mipad2/wcove and surface3/ccove).

> I've also figured out all the other chips used in the Mi Pad 2
> and I believe I should be able to get things battery monitoring
> and switching the USB plug between host <-> device mode to work
> without too much issues (but it will take some time). This is
> all pretty similar to all the special handling which I've already
> added to the kernel for the GPD win / pocket devices which also
> use the CHT Whiskey Cove PMIC.

Thanks. I haven't looked into anything other than atomisp yet, so I
can't comment anything but it's really interesting to see how drivers
are developed :-)

> Here are my notes about all the non standard chips used in the
> Mi Pad 2:
>
> PMIC/charger/fuel-gauge:
> -The Type-C connector is used as / wired up as a regular micro-USB connector
>
> -There is a Cherry Trail Whiskey Cove PMIC on the I2C7 i2c_designware ctrl
> -This is used for ID pin detection
> -Charger-type detection does not work though, because the USB-2 data-lines are
> not connected to it
> -The 2 GPIOs which are used to enable an external V5 boost converter for
> Vbus resp Vconn on other designs are both configured as inputs (register value 0x18)
> -The extcon-intel-cht-wc driver should control the USB mux according to the
> ID pin, identically to how the extcon-axp288 code does this
> -The extcon-intel-cht-wc driver should control the Vboost converter in the
> bq25890 charger IC based on the ID pin
>
> -There is a bq25890 charger hanging from the CHT-WC PMIC charger I2C-bus at addr 0x6a
> -At boot the BIOS clears bit 4 of register 3, disabling charging so the device
> will still be powered from an external supply, but it will not charge!
> Linux needs to fix this up
> -This charger is connected to the USB-2 data-lines and automatically sets its
> input-current-limit based on the detected charger
> -Bit 5 of register 3 controls the Vboost converter for sending 5V to attached
> USB-devices this bit needs to be controller by Linux based on the ID pin
> detection from the PMIC. The BIOS does leave this enabled when booting with
> a USB-device plugged in.
>
> -There is a BQ27520 fuel-gauge at address 0x55 of the I2C1 i2c_designware ctrl
>
> I2C1: addr 0x55 BQ27520 fuel-gauge
>
> I2C2: addr 0x0e unknown
> I2C2: addr 0x1b Realtek 5659 codec ? (not detected by i2cdetect)
> I2C2: addr 0x2c TI lp855x backlight controller:
> https://github.com/MiCode/Xiaomi_Kernel_OpenSource/blob/latte-l-oss/drivers/video/backlight/lp855x_bl.c
> I2C2: addr 0x34 NXP9890 audio amplifier
> I2C2: addr 0x37 NXP9890 audio amplifier
> I2C2: addr 0x3e unknown
>
> I2C3: addr 0x30 KTD2026 RGB LED driver, controlling the status LED
> https://github.com/MiCode/Xiaomi_Kernel_OpenSource/blob/latte-l-oss/drivers/leds/leds-ktd2026.c
>
> I2C4: addr 0x36? OVTI5693 camera sensor
> I2C4: addr 0x37 t3ka3 camera sensor
>
> I2C5: addr 0x5a Motor DRV2604 Driver ? the tablet has no haptic feedback motor!
> Also nothing seen here by i2c-detect, probably bogus

This must be a motor for the world-facing camera! I see "DW9761" in DSDT.
Currently, I have no idea if motors are working with the upstreamed
atomisp because there is no userspace driver for Linux that can use
motors.

Regards,
Tsuchiya Yuto

> I2C6: addr 0x38 FTSC touchscreen
>
> I2C7: PMIC bus
>
> -TPS61158: LED controller for menu keys LEDS, driven by PWM controller, max brightness
> 80/255 !!!!
> https://github.com/MiCode/Xiaomi_Kernel_OpenSource/blob/latte-l-oss/drivers/leds/leds-tps61158.c
> Android behavior: light up menu keys for 5 seconds on any human input:
> -Write a special HID driver for mainline linux to fix the key-events send by the
> touchscreen and to light up the keys for 5 seconds on any HID input reports
>
> -Sensors (accel, als) through hid-ishtp
>
> -Panel 1536x2048 on card0-DSI-1
> https://bugs.freedesktop.org/show_bug.cgi?id=108714
>
> -DSDT: Android: OSID == 0x04, Windows OSID == 0x01
>
> Regards,
>
> Hans


\
 
 \ /
  Last update: 2021-10-26 11:36    [W:0.169 / U:0.080 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site