[lkml]   [2021]   [Jan]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
Messages in this thread
Patch in this message
Subject[PATCH] x86/hyperv: Initialize clockevents after LAPIC is initialized
With commit 4df4cb9e99f8, the Hyper-V direct-mode STIMER is actually
initialized before LAPIC is initialized: see




setup_local_APIC() temporarily disables LAPIC, initializes it and
re-eanble it. The direct-mode STIMER depends on LAPIC, and when it's
registered, it can be programmed immediately and the timer can fire
very soon:

tick_setup_periodic(), tick_setup_oneshot()

When the timer fires in the hypervisor, if the LAPIC is in the
disabled state, new versions of Hyper-V ignore the event and don't inject
the timer interrupt into the VM, and hence the VM hangs when it boots.

Note: when the VM starts/reboots, the LAPIC is pre-enabled by the
firmware, so the window of LAPIC being temporarily disabled is pretty
small, and the issue can only happen once out of 100~200 reboots for
a 40-vCPU VM on one dev host, and on another host the issue doesn't
reproduce after 2000 reboots.

The issue is more noticeable for kdump/kexec, because the LAPIC is
disabled by the first kernel, and stays disabled until the kdump/kexec
kernel enables it. This is especially an issue to a Generation-2 VM
(for which Hyper-V doesn't emulate the PIT timer) when CONFIG_HZ=1000
(rather than CONFIG_HZ=250) is used.

Fix the issue by moving hv_stimer_alloc() to a later place where the
LAPIC timer is initialized.

Fixes: 4df4cb9e99f8 ("x86/hyperv: Initialize clockevents earlier in CPU onlining")
Signed-off-by: Dexuan Cui <>
arch/x86/hyperv/hv_init.c | 29 ++++++++++++++++++++++++++---
1 file changed, 26 insertions(+), 3 deletions(-)

diff --git a/arch/x86/hyperv/hv_init.c b/arch/x86/hyperv/hv_init.c
index 4638a52d8eae..6375967a8244 100644
--- a/arch/x86/hyperv/hv_init.c
+++ b/arch/x86/hyperv/hv_init.c
@@ -315,6 +315,25 @@ static struct syscore_ops hv_syscore_ops = {
.resume = hv_resume,

+static void (* __initdata old_setup_percpu_clockev)(void);
+static void __init hv_stimer_setup_percpu_clockev(void)
+ /*
+ * Ignore any errors in setting up stimer clockevents
+ * as we can run with the LAPIC timer as a fallback.
+ */
+ (void)hv_stimer_alloc();
+ /*
+ * Still register the LAPIC timer, because the direct-mode STIMER is
+ * not supported by old versions of Hyper-V. This also allows users
+ * to switch to LAPIC timer via /sys, if they want to.
+ */
+ if (old_setup_percpu_clockev)
+ old_setup_percpu_clockev();
* This function is to be invoked early in the boot sequence after the
* hypervisor has been detected.
@@ -393,10 +412,14 @@ void __init hyperv_init(void)
wrmsrl(HV_X64_MSR_HYPERCALL, hypercall_msr.as_uint64);

- * Ignore any errors in setting up stimer clockevents
- * as we can run with the LAPIC timer as a fallback.
+ * hyperv_init() is called before LAPIC is initialized: see
+ * apic_intr_mode_init() -> x86_platform.apic_post_init() and
+ * apic_bsp_setup() -> setup_local_APIC(). The direct-mode STIMER
+ * depends on LAPIC, so hv_stimer_alloc() should be called from
+ * x86_init.timers.setup_percpu_clockev.
- (void)hv_stimer_alloc();
+ old_setup_percpu_clockev = x86_init.timers.setup_percpu_clockev;
+ x86_init.timers.setup_percpu_clockev = hv_stimer_setup_percpu_clockev;


 \ /
  Last update: 2021-01-16 23:34    [W:0.067 / U:1.740 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site