lkml.org 
[lkml]   [2020]   [Mar]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2] pinctrl: qcom: use scm_call to route GPIO irq to Apps
Date
From: Ajay Kishore <akisho@codeaurora.org>

For IPQ806x targets, TZ protects the registers that are used to
configure the routing of interrupts to a target processor.
To resolve this, this patch uses scm call to route GPIO interrupts
to application processor. Also the scm call interface is changed.

Signed-off-by: Ajay Kishore <akisho@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
---
v2:
* Move static varibale in msm_pinctrl struct
* Revert '4b024225c4a8 ("pinctrl: use devm_platform_ioremap_resource() to simplify code")'
to get base_reg addr

drivers/pinctrl/qcom/pinctrl-msm.c | 37 ++++++++++++++++++++++++++----
1 file changed, 32 insertions(+), 5 deletions(-)

diff --git a/drivers/pinctrl/qcom/pinctrl-msm.c b/drivers/pinctrl/qcom/pinctrl-msm.c
index 9a8daa256a32..9627ebd41ff9 100644
--- a/drivers/pinctrl/qcom/pinctrl-msm.c
+++ b/drivers/pinctrl/qcom/pinctrl-msm.c
@@ -22,6 +22,8 @@
#include <linux/reboot.h>
#include <linux/pm.h>
#include <linux/log2.h>
+#include <linux/qcom_scm.h>
+#include <linux/io.h>

#include <linux/soc/qcom/irq.h>

@@ -60,6 +62,9 @@ struct msm_pinctrl {
struct irq_chip irq_chip;
int irq;

+ int route_to_apps;
+ u32 base_reg;
+
raw_spinlock_t lock;

DECLARE_BITMAP(dual_edge_irqs, MAX_NR_GPIO);
@@ -883,10 +888,27 @@ static int msm_gpio_irq_set_type(struct irq_data *d, unsigned int type)
clear_bit(d->hwirq, pctrl->dual_edge_irqs);

/* Route interrupts to application cpu */
- val = msm_readl_intr_target(pctrl, g);
- val &= ~(7 << g->intr_target_bit);
- val |= g->intr_target_kpss_val << g->intr_target_bit;
- msm_writel_intr_target(val, pctrl, g);
+ if (pctrl->route_to_apps && pctrl->base_reg) {
+ u32 addr = pctrl->base_reg + g->intr_target_reg;
+ int ret;
+
+ qcom_scm_io_readl(addr, &val);
+
+ val &= ~(7 << g->intr_target_bit);
+ val |= g->intr_target_kpss_val << g->intr_target_bit;
+
+ ret = qcom_scm_io_writel(addr, val);
+ if (ret)
+ dev_err(pctrl->dev,
+ "Failed routing %lu interrupt to Apps proc",
+ d->hwirq);
+ }
+ } else {
+ val = msm_readl_intr_target(pctrl, g);
+ val &= ~(7 << g->intr_target_bit);
+ val |= g->intr_target_kpss_val << g->intr_target_bit;
+ msm_writel_intr_target(val, pctrl, g);
+ }

/* Update configuration for gpio.
* RAW_STATUS_EN is left on for all gpio irqs. Due to the
@@ -1241,6 +1263,8 @@ int msm_pinctrl_probe(struct platform_device *pdev,
pctrl->dev = &pdev->dev;
pctrl->soc = soc_data;
pctrl->chip = msm_gpio_template;
+ pctrl->route_to_apps = of_device_is_compatible(pctrl->dev->of_node,
+ "qcom,ipq8064-pinctrl");

raw_spin_lock_init(&pctrl->lock);

@@ -1253,9 +1277,12 @@ int msm_pinctrl_probe(struct platform_device *pdev,
return PTR_ERR(pctrl->regs[i]);
}
} else {
- pctrl->regs[0] = devm_platform_ioremap_resource(pdev, 0);
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ pctrl->regs[0] = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(pctrl->regs[0]))
return PTR_ERR(pctrl->regs[0]);
+ else
+ pctrl->base_reg = res->start;
}

msm_pinctrl_setup_pm_reset(pctrl);
--
2.25.1
\
 
 \ /
  Last update: 2020-03-26 18:37    [W:0.346 / U:0.024 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site