lkml.org 
[lkml]   [2020]   [Nov]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Subject[RFC PATCH v3.1 00/27] Add support UHS-II for GL9755
Date
This is an interim snapshot of our next version, v4, for enabling
UHS-II on MMC/SD.

It is focused on 'sdhci' side to address Adrian's comments regarding
"modularising" sdhci-uhs2.c.
The whole aim of this version is to get early feedback from Adrian (and
others) on this issue. Without any consensus about the code structure,
it would make little sense to go further ahead on sdhci side.
(Actually, Adrian has made no comments other than "modularising" so far.)

I heavily reworked/refactored sdhci-uhs2.c and re-organised the patch
set to meet what I believe Adrian expects; no UHS-II related code in
Legacy (UHS-I) code or sdhci.c.

Nevertheless, almost of all changes I made are trivial and straightforward
in this direction, and I believe that there is no logic changed since v3
except sdhci_uhs2_irq(), as ops->irq hook, where we must deal with UHS-II
command sequences in addition to UHS-II errors. So I added extra handlings.

I admit that there is plenty of room for improvements (for example,
handling host->flags), but again the focal point here is how sdhci-uhs2.c
should be built as a module.

Please review this series (particularly Patch#8-#26 and #27) from this
viewpoint in the first place.
(Ben is working on 'host' side but there is no change on 'host' side
in this submission except a minor tweak.)

Thanks,
-Takahiro Akashi

------ original cover letter from v3 ------
Summary
=======
These patches[1] support UHS-II and fix GL9755 UHS-II compatibility.

About UHS-II, roughly deal with the following three parts:
1) A UHS-II detection and initialization:
- Host setup to support UHS-II (Section 3.13.1 Host Controller Setup Sequence
[2]).
- Detect a UHS-II I/F (Section 3.13.2 Card Interface Detection Sequence[2]).
- In step(9) of Section 3.13.2 in [2], UHS-II initialization is include Section
3.13.3 UHS-II Card Initialization and Section 3.13.4 UHS-II Setting Register
Setup Sequence.

2) Send Legacy SD command through SD-TRAN
- Encapsulated SD packets are defined in SD-TRAN in order to ensure Legacy SD
compatibility and preserve Legacy SD infrastructures (Section 7.1.1 Packet
Types and Format Overview[3]).
- Host issue a UHS-II CCMD packet or a UHS-II DCMD (Section 3.13.5 UHS-II
CCMD Packet issuing and Section 3.13.6 UHS-II DCMD Packet issuing[2]).

3) UHS-II Interrupt
- Except for UHS-II error interrupts, most interrupts share the original
interrupt registers.

Patch structure
===============
patch#1-#7: for core
patch#8-#17: for sdhci
patch#18-#21: for GL9755

Tests
=====
Ran 'dd' command to evaluate the performance:
(SanDisk UHS-II card on GL9755 controller)
Read Write
UHS-II disabled (UHS-I): 88.3MB/s 60.7MB/s
UHS-II enabled : 206MB/s 80MB/s

TODO
====
- replace some define with BIT macro

Reference
=========
[1] https://gitlab.com/ben.chuang/linux-uhs2-gl9755.git
[2] SD Host Controller Simplified Specification 4.20
[3] UHS-II Simplified Addendum 1.02

Changes in v3 (Jul. 10, 2020)
* rebased to v5.8-rc4
* add copyright notice
* reorganize the patch set and split some commits into smaller ones
* separate uhs-2 headers from others
* correct wrong spellings
* fix most of checkpatch warnings/errors
* remove all k[cz]alloc() from the code
* guard sdhci-uhs2 specific code with
'if (IS_ENABLED(CONFIG_MMC_SDHCI_UHS2))'
* make sdhci-uhs2.c as a module
* trivial changes, including
- rename back sdhci-core.c to sdhci.c
- allow vendor code to disable uhs2 if v4_mode == 0
in __sdhci_add_host()
- merge uhs2_power_up() into mmc_power_up()
- remove flag_uhs2 from mmc_attach_sd()
- add function descriptions to EXPORT'ed functions
- other minor code optimization

Changes in v2 (Jan. 9, 2020)
* rebased to v5.5-rc5

AKASHI Takahiro (23):
mmc: core: UHS-II support, modify power-up sequence
mmc: core: UHS-II support, skip set_chip_select()
mmc: core: UHS-II support, skip TMODE setup in some cases
mmc: core: UHS-II support, generate UHS-II SD command packet
mmc: core: UHS-II support, set APP_CMD bit if necessary
mmc: sdhci: add a kernel configuration for enabling UHS-II support
mmc: sdhci: add UHS-II related definitions in headers
mmc: sdhci: add UHS-II module
mmc: sdhci-uhs2: dump UHS-II registers
mmc: sdhci-uhs2: add reset function
mmc: sdhci-uhs2: add set_power() to support vdd2
mmc: sdhci-uhs2: skip signal_voltage_switch()
mmc: sdhci-uhs2: add set_timeout()
mmc: sdhci-uhs2: add set_ios()
mmc: sdhci-uhs2: add detect_init() to detect the interface
mmc: sdhci-uhs2: add clock operations
mmc: sdhci-uhs2: add set_reg() to initialise the interface
mmc: sdhci-uhs2: add request() and others
mmc: sdhci-uhs2: add irq() and others
mmc: sdhci-uhs2: add add_host() and others to set up the driver
mmc: core: add post-mmc_attach_sd hook
mmc: sdhci-pci: add UHS-II support framework
mmc: sdhci-pci-gli: enable UHS-II mode for GL9755

Ben Chuang (4):
mmc: add UHS-II related definitions in public headers
mmc: core: UHS-II support, try to select UHS-II interface
mmc: sdhci-uhs2: add pre-detect_init hook
mmc: sdhci-uhs2: add post-mmc_attach_sd hook

drivers/mmc/core/Makefile | 2 +-
drivers/mmc/core/block.c | 7 +-
drivers/mmc/core/bus.c | 5 +-
drivers/mmc/core/core.c | 118 +-
drivers/mmc/core/regulator.c | 14 +
drivers/mmc/core/sd.c | 32 +
drivers/mmc/core/sd_ops.c | 12 +
drivers/mmc/core/uhs2.c | 883 +++++++++++++++
drivers/mmc/core/uhs2.h | 21 +
drivers/mmc/host/Kconfig | 10 +
drivers/mmc/host/Makefile | 1 +
drivers/mmc/host/sdhci-pci-core.c | 16 +-
drivers/mmc/host/sdhci-pci-gli.c | 318 +++++-
drivers/mmc/host/sdhci-pci.h | 3 +
drivers/mmc/host/sdhci-uhs2.c | 1697 +++++++++++++++++++++++++++++
drivers/mmc/host/sdhci-uhs2.h | 224 ++++
drivers/mmc/host/sdhci.c | 333 +++---
drivers/mmc/host/sdhci.h | 117 +-
include/linux/mmc/card.h | 1 +
include/linux/mmc/core.h | 6 +
include/linux/mmc/host.h | 31 +
include/linux/mmc/uhs2.h | 268 +++++
22 files changed, 3961 insertions(+), 158 deletions(-)
create mode 100644 drivers/mmc/core/uhs2.c
create mode 100644 drivers/mmc/core/uhs2.h
create mode 100644 drivers/mmc/host/sdhci-uhs2.c
create mode 100644 drivers/mmc/host/sdhci-uhs2.h
create mode 100644 include/linux/mmc/uhs2.h

--
2.28.0

\
 
 \ /
  Last update: 2020-11-06 03:28    [W:0.360 / U:1.548 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site