lkml.org 
[lkml]   [2019]   [Sep]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 6/8] ARM: dts: omap36xx: using OPP1G needs to control the abb_ldo
Date
See DM3730,DM275 data sheet (SPRS685B) footnote (6) in Table 4-19
which says that ABB must be switched to FBB mode when using the
OPP1G.

The LOD definition abb_mpu_iva already exists so that we need
to add plumbing for vbb-supply = <&abb_mpu_iva>
and define two voltage vectors for each OPP so that the abb LDO
is also updated by the ti-cpufreq driver.

We also must switch the ti_cpufreq_soc_data to multi_regulator.

Note: reading out the abb reglator voltage to verify that
it does do transitions can be done by

cat /sys/devices/platform/68000000.ocp/483072f0.regulator-abb-mpu/regulator/regulator.*/microvolts

Likewise, read the twl4030 provided VDD voltage by

cat /sys/devices/platform/68000000.ocp/48070000.i2c/i2c-0/0-0048/48070000.i2c:twl@48:regulator-vdd1/regulator/regulator.*/microvolts

Note: to check if the ABB FBB is enabled/disabled, check
registers

PRM_LDO_ABB_CTRL 0x483072F4 bit 3:0 1=bypass 5=FBB
PRM_LDO_ABB_SETUP 0x483072F0 0x00=bypass 0x11=FBB

e.g.

/dev/mem opened.
Memory mapped at address 0xb6fe4000.
Value at address 0x483072F4 (0xb6fe42f4): 0x3205
/dev/mem opened.
Memory mapped at address 0xb6f89000.
Value at address 0x483072F4 (0xb6f892f4): 0x3201

Note: omap34xx and am3517 have/need no comparable LDO
or mechanism.

Suggested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
arch/arm/boot/dts/omap36xx.dtsi | 21 ++++++++++++++++-----
drivers/cpufreq/ti-cpufreq.c | 2 +-
2 files changed, 17 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/omap36xx.dtsi b/arch/arm/boot/dts/omap36xx.dtsi
index cb5bd0969124..4bb4f534afe2 100644
--- a/arch/arm/boot/dts/omap36xx.dtsi
+++ b/arch/arm/boot/dts/omap36xx.dtsi
@@ -23,6 +23,7 @@
cpu: cpu@0 {
operating-points-v2 = <&cpu0_opp_table>;

+ vbb-supply = <&abb_mpu_iva>;
clock-latency = <300000>; /* From omap-cpufreq driver */
};
};
@@ -37,9 +38,11 @@
/*
* we currently only select the max voltage from table
* Table 4-19 of the DM3730 Data sheet (SPRS685B)
- * Format is: <target min max>
+ * Format is: cpu0-supply: <target min max>
+ * vbb-supply: <target min max>
*/
- opp-microvolt = <1012500 1012500 1012500>;
+ opp-microvolt = <1012500 1012500 1012500>,
+ <1012500 1012500 1012500>;
/*
* first value is silicon revision bit mask
* second one is "speed binned" bit mask
@@ -50,25 +53,33 @@

opp100-600000000 {
opp-hz = /bits/ 64 <600000000>;
- opp-microvolt = <1200000 1200000 1200000>;
+ opp-microvolt = <1200000 1200000 1200000>,
+ <1200000 1200000 1200000>;
opp-supported-hw = <0xffffffff 3>;
};

opp130-800000000 {
opp-hz = /bits/ 64 <800000000>;
- opp-microvolt = <1325000 1325000 1325000>;
+ opp-microvolt = <1325000 1325000 1325000>,
+ <1325000 1325000 1325000>;
opp-supported-hw = <0xffffffff 3>;
};

opp1g-1000000000 {
opp-hz = /bits/ 64 <1000000000>;
- opp-microvolt = <1375000 1375000 1375000>;
+ opp-microvolt = <1375000 1375000 1375000>,
+ <1375000 1375000 1375000>;
/* only on am/dm37x with speed-binned bit set */
opp-supported-hw = <0xffffffff 2>;
turbo-mode;
};
};

+ opp_supply_mpu_iva: opp_supply {
+ compatible = "ti,omap-opp-supply";
+ ti,absolute-max-voltage-uv = <1375000>;
+ };
+
ocp@68000000 {
uart4: serial@49042000 {
compatible = "ti,omap3-uart";
diff --git a/drivers/cpufreq/ti-cpufreq.c b/drivers/cpufreq/ti-cpufreq.c
index 1a3073a3093e..f4704f9033e0 100644
--- a/drivers/cpufreq/ti-cpufreq.c
+++ b/drivers/cpufreq/ti-cpufreq.c
@@ -174,7 +174,7 @@ static struct ti_cpufreq_soc_data omap36xx_soc_data = {
.efuse_shift = 9,
.efuse_mask = BIT(9),
.rev_offset = OMAP3_CONTROL_IDCODE - OMAP3_SYSCON_BASE,
- .multi_regulator = false,
+ .multi_regulator = true,
};

/**
--
2.19.1
\
 
 \ /
  Last update: 2019-09-11 19:48    [W:0.826 / U:1.672 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site