lkml.org 
[lkml]   [2019]   [Jun]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [linux-sunxi] [PATCH v6 5/6] drm: sun4i: Add support for enabling DDC I2C bus to sun8i_dw_hdmi glue
Hi Jernej,

On Sun, Jun 16, 2019 at 01:05:13PM +0200, Jernej Škrabec wrote:
> Hi Ondrej!
>
> Dne ponedeljek, 27. maj 2019 ob 18:22:36 CEST je megous via linux-sunxi
> napisal(a):
> > From: Ondrej Jirman <megous@megous.com>
> >
> > Orange Pi 3 board requires enabling a voltage shifting circuit via GPIO
> > for the DDC bus to be usable.
> >
> > Add support for hdmi-connector node's optional ddc-en-gpios property to
> > support this use case.
> >
> > Signed-off-by: Ondrej Jirman <megous@megous.com>
> > ---
> > drivers/gpu/drm/sun4i/sun8i_dw_hdmi.c | 55 +++++++++++++++++++++++++--
> > drivers/gpu/drm/sun4i/sun8i_dw_hdmi.h | 3 ++
> > 2 files changed, 55 insertions(+), 3 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/sun4i/sun8i_dw_hdmi.c
> > b/drivers/gpu/drm/sun4i/sun8i_dw_hdmi.c index 39d8509d96a0..59b81ba02d96
> > 100644
> > --- a/drivers/gpu/drm/sun4i/sun8i_dw_hdmi.c
> > +++ b/drivers/gpu/drm/sun4i/sun8i_dw_hdmi.c
> > @@ -98,6 +98,30 @@ static u32 sun8i_dw_hdmi_find_possible_crtcs(struct
> > drm_device *drm, return crtcs;
> > }
> >
> > +static int sun8i_dw_hdmi_find_connector_pdev(struct device *dev,
> > + struct
> platform_device **pdev_out)
> > +{
> > + struct platform_device *pdev;
> > + struct device_node *remote;
> > +
> > + remote = of_graph_get_remote_node(dev->of_node, 1, -1);
> > + if (!remote)
> > + return -ENODEV;
> > +
> > + if (!of_device_is_compatible(remote, "hdmi-connector")) {
> > + of_node_put(remote);
> > + return -ENODEV;
> > + }
> > +
> > + pdev = of_find_device_by_node(remote);
> > + of_node_put(remote);
> > + if (!pdev)
> > + return -ENODEV;
> > +
> > + *pdev_out = pdev;
> > + return 0;
> > +}
> > +
> > static int sun8i_dw_hdmi_bind(struct device *dev, struct device *master,
> > void *data)
> > {
> > @@ -151,16 +175,29 @@ static int sun8i_dw_hdmi_bind(struct device *dev,
> > struct device *master, return PTR_ERR(hdmi->regulator);
> > }
> >
> > + ret = sun8i_dw_hdmi_find_connector_pdev(dev, &hdmi->connector_pdev);
> > + if (!ret) {
> > + hdmi->ddc_en = gpiod_get_optional(&hdmi->connector_pdev-
> >dev,
> > + "ddc-en",
> GPIOD_OUT_HIGH);
> > + if (IS_ERR(hdmi->ddc_en)) {
> > + platform_device_put(hdmi->connector_pdev);
> > + dev_err(dev, "Couldn't get ddc-en gpio\n");
> > + return PTR_ERR(hdmi->ddc_en);
> > + }
> > + }
> > +
> > ret = regulator_enable(hdmi->regulator);
> > if (ret) {
> > dev_err(dev, "Failed to enable regulator\n");
> > - return ret;
> > + goto err_unref_ddc_en;
> > }
> >
> > + gpiod_set_value(hdmi->ddc_en, 1);
>
> Why don't you do that inside if clause where hdmi->ddc_en is assigned? It's
> not useful otherwise anyway.
>
> Besides, you would then only need to adjust one goto label in error path.

The idea is to enable DDC after enabling the regulator. I don't think it matters
for the particular HW that's on Orange Pi 3, and similar Xunlong boards, but
this is a fairly generic binding and it makes more sense to power the bus, and
then enable whatever aditional circuitry might be there for the IO.

I can move sun8i_dw_hdmi_find_connector_pdev lower, but I would then need to
disable the regulator in the error path, and I like to keep this order:

- parsing DT
- enabling actual HW stuff

Because parsing is likely to fail with DEFERED_PROBE, because GPIO or whatever
else is not yet ready, and this approach avoids enabling/disabling the HW
needlessly.

> > +
> > ret = reset_control_deassert(hdmi->rst_ctrl);
> > if (ret) {
> > dev_err(dev, "Could not deassert ctrl reset
> control\n");
> > - goto err_disable_regulator;
> > + goto err_disable_ddc_en;
> > }
> >
> > ret = clk_prepare_enable(hdmi->clk_tmds);
> > @@ -213,8 +250,14 @@ static int sun8i_dw_hdmi_bind(struct device *dev,
> > struct device *master, clk_disable_unprepare(hdmi->clk_tmds);
> > err_assert_ctrl_reset:
> > reset_control_assert(hdmi->rst_ctrl);
> > -err_disable_regulator:
> > +err_disable_ddc_en:
> > + gpiod_set_value(hdmi->ddc_en, 0);
> > regulator_disable(hdmi->regulator);
> > +err_unref_ddc_en:
> > + if (hdmi->ddc_en)
> > + gpiod_put(hdmi->ddc_en);
> > +
> > + platform_device_put(hdmi->connector_pdev);
> >
> > return ret;
> > }
> > @@ -228,7 +271,13 @@ static void sun8i_dw_hdmi_unbind(struct device *dev,
> > struct device *master, sun8i_hdmi_phy_remove(hdmi);
> > clk_disable_unprepare(hdmi->clk_tmds);
> > reset_control_assert(hdmi->rst_ctrl);
> > + gpiod_set_value(hdmi->ddc_en, 0);
> > regulator_disable(hdmi->regulator);
> > +
> > + if (hdmi->ddc_en)
> > + gpiod_put(hdmi->ddc_en);
> > +
> > + platform_device_put(hdmi->connector_pdev);
> > }
> >
> > static const struct component_ops sun8i_dw_hdmi_ops = {
> > diff --git a/drivers/gpu/drm/sun4i/sun8i_dw_hdmi.h
> > b/drivers/gpu/drm/sun4i/sun8i_dw_hdmi.h index 720c5aa8adc1..dad66b8301c2
> > 100644
> > --- a/drivers/gpu/drm/sun4i/sun8i_dw_hdmi.h
> > +++ b/drivers/gpu/drm/sun4i/sun8i_dw_hdmi.h
> > @@ -9,6 +9,7 @@
> > #include <drm/bridge/dw_hdmi.h>
> > #include <drm/drm_encoder.h>
> > #include <linux/clk.h>
> > +#include <linux/gpio/consumer.h>
> > #include <linux/regmap.h>
> > #include <linux/regulator/consumer.h>
> > #include <linux/reset.h>
> > @@ -190,6 +191,8 @@ struct sun8i_dw_hdmi {
> > struct regulator *regulator;
> > const struct sun8i_dw_hdmi_quirks *quirks;
> > struct reset_control *rst_ctrl;
> > + struct platform_device *connector_pdev;
>
> It seems that connector_pdev is needed only during intialization. Why do you
> store it?

For some reason I thought that I need to keep it to keep the GPIO available,
but that's not true. I'll drop it.

thank you,
Ondrej

> Best regards,
> Jernej
>
> > + struct gpio_desc *ddc_en;
> > };
> >
> > static inline struct sun8i_dw_hdmi *

\
 
 \ /
  Last update: 2019-06-16 14:50    [W:0.043 / U:9.476 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site