lkml.org 
[lkml]   [2019]   [Dec]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH V3 1/2] dt-bindings/irq: add binding for NXP INTMUX interrupt multiplexer
Date

> -----Original Message-----
> From: Joakim Zhang <qiangqing.zhang@nxp.com>
> Sent: 2019年12月20日 15:37
> To: maz@kernel.org; tglx@linutronix.de; jason@lakedaemon.net;
> robh+dt@kernel.org; mark.rutland@arm.com; shawnguo@kernel.org;
> s.hauer@pengutronix.de
> Cc: kernel@pengutronix.de; dl-linux-imx <linux-imx@nxp.com>;
> linux-kernel@vger.kernel.org; Andy Duan <fugang.duan@nxp.com>;
> linux-arm-kernel@lists.infradead.org; Joakim Zhang
> <qiangqing.zhang@nxp.com>
> Subject: [PATCH V3 1/2] dt-bindings/irq: add binding for NXP INTMUX interrupt
> multiplexer
>
> This patch adds the DT bindings for the NXP INTMUX interrupt multiplexer for
> i.MX8 family SoCs.
>
> Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
> ---
> .../interrupt-controller/fsl,intmux.txt | 36 +++++++++++++++++++
> 1 file changed, 36 insertions(+)
> create mode 100644
> Documentation/devicetree/bindings/interrupt-controller/fsl,intmux.txt
>
> diff --git
> a/Documentation/devicetree/bindings/interrupt-controller/fsl,intmux.txt
> b/Documentation/devicetree/bindings/interrupt-controller/fsl,intmux.txt
> new file mode 100644
> index 000000000000..3ebe9cac5f20
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/interrupt-controller/fsl,intmux.
> +++ txt
> @@ -0,0 +1,36 @@
> +Freescale INTMUX interrupt multiplexer
> +
> +Required properties:
> +
> +- compatible: Should be:
> + - "fsl,imx-intmux"
> +- reg: Physical base address and size of registers.
> +- interrupts: Should contain the parent interrupt lines (up to 8) used
> +to
> + multiplex the input interrupts.
> +- clocks: Should contain one clock for entry in clock-names.
> +- clock-names:
> + - "ipg": main logic clock
> +- interrupt-controller: Identifies the node as an interrupt controller.
> +- #interrupt-cells: Specifies the number of cells needed to encode an
> + interrupt source. The value must be 2.
> + - the 1st cell: hardware interrupt number
> + - the 2nd cell: channel index, value must smaller than channels used
> +
> +Optional properties:
> +
> +- fsl,intmux_chans: The number of channels used for interrupt source.
> +The
> + Maximum value is 8. If this property is not set in DT then driver
> +uses
> + 1 channel by default.
> +
> +Example:
> +
> + intmux@37400000 {
> + compatible = "fsl,imx-intmux";
> + reg = <0x37400000 0x1000>;
> + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clk IMX8QM_CM40_IPG_CLK>;
> + clock-names = "ipg";
> + interrupt-controller;
> + #interrupt-cells = <1>;
Hi Marc,

I am so sorry, this should be #interrupt-cells = <2>, will correct it in next version.

Best Regards,
Joakim Zhang
> + };
> +
> --
> 2.17.1

\
 
 \ /
  Last update: 2019-12-20 08:45    [W:0.322 / U:0.052 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site