lkml.org 
[lkml]   [2019]   [Oct]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH V2 1/3] arm64: dts: imx8mm-evk: Adjust i2c nodes following alphabetical sort
Date
The iomuxc node is being put at end of file because of its huge
pinctrl data. I2C devices should be placed in alphabetical sort.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
new patch.
---
arch/arm64/boot/dts/freescale/imx8mm-evk.dts | 124 +++++++++++++--------------
1 file changed, 62 insertions(+), 62 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
index f7a15f3..f6d367c 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
@@ -94,68 +94,6 @@
};
};

-&sai3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_sai3>;
- assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
- assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
- assigned-clock-rates = <24576000>;
- status = "okay";
-};
-
-&snvs_pwrkey {
- status = "okay";
-};
-
-&uart2 { /* console */
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
- status = "okay";
-};
-
-&usbotg1 {
- dr_mode = "otg";
- hnp-disable;
- srp-disable;
- adp-disable;
- usb-role-switch;
- status = "okay";
-
- port {
- usb1_drd_sw: endpoint {
- remote-endpoint = <&typec1_dr_sw>;
- };
- };
-};
-
-&usdhc2 {
- pinctrl-names = "default", "state_100mhz", "state_200mhz";
- pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
- pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
- pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
- cd-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
- bus-width = <4>;
- vmmc-supply = <&reg_usdhc2_vmmc>;
- status = "okay";
-};
-
-&usdhc3 {
- pinctrl-names = "default", "state_100mhz", "state_200mhz";
- pinctrl-0 = <&pinctrl_usdhc3>;
- pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
- pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
- bus-width = <8>;
- non-removable;
- status = "okay";
-};
-
-&wdog1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_wdog>;
- fsl,ext-reset-output;
- status = "okay";
-};
-
&i2c1 {
clock-frequency = <400000>;
pinctrl-names = "default";
@@ -306,6 +244,68 @@
};
};

+&sai3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai3>;
+ assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
+ assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
+ assigned-clock-rates = <24576000>;
+ status = "okay";
+};
+
+&snvs_pwrkey {
+ status = "okay";
+};
+
+&uart2 { /* console */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&usbotg1 {
+ dr_mode = "otg";
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+ usb-role-switch;
+ status = "okay";
+
+ port {
+ usb1_drd_sw: endpoint {
+ remote-endpoint = <&typec1_dr_sw>;
+ };
+ };
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ cd-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ vmmc-supply = <&reg_usdhc2_vmmc>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
&iomuxc {
pinctrl-names = "default";

--
2.7.4
\
 
 \ /
  Last update: 2019-10-08 03:28    [W:0.060 / U:1.220 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site