lkml.org 
[lkml]   [2018]   [Aug]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH V3] spi: spi-geni-qcom: Add SPI driver support for GENI based QUP
On Fri, Aug 24, 2018 at 04:12:15PM +0530, Dilip Kota wrote:
> From: Girish Mahadevan <girishm@codeaurora.org>
>
> This driver supports GENI based SPI Controller in the Qualcomm SOCs. The
> Qualcomm Generic Interface (GENI) is a programmable module supporting a
> wide range of serial interfaces including SPI. This driver supports SPI
> operations using FIFO mode of transfer.
>
> Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
> Signed-off-by: Dilip Kota <dkota@codeaurora.org>
> ---
> Addressing all the reviewer commets given in Patchset1.
> Summerizing all the comments below:
>
> MAKEFILE: Arrange SPI-GENI driver in alphabetical order
> Kconfig: Mark SPI_GENI driver dependent on QCOM_GENI_SE
> Enable SPI core auto runtime pm, and remove runtime pm calls.
> Remove spi_geni_unprepare_message(), spi_geni_unprepare_transfer_hardware()
> Remove likely/unlikely keywords.
> Remove get_spi_master() and use dev_get_drvdata()
> Move request_irq to probe()
> Mark bus number assignment to -1 as SPI core framework will assign dynamically
> Use devm_spi_register_master()
> Include platform_device.h instead of of_platform.h
> Removing macros which are used only once:
> #define SPI_NUM_CHIPSELECT 4
> #define SPI_XFER_TIMEOUT_MS 250
> Place Register field definitions next to respective Register definitions.
> Replace int and u32 declerations to unsigned int.
> Remove Hex numbers in debug prints.
> Declare mode as u16 in spi_setup_word_len()
> Remove the labels: setup_fifo_params_exit: exit_prepare_transfer_hardware:
> Declaring struct spi_master as spi everywhere in the file.
> Calling spi_finalize_current_transfer() for end of transfer.
> Hard code the SPI controller max frequency instead of reading from DTSI node.
> Spinlock not required, removed it.
> Removed unrequired error prints.
> Fix KASAN error in geni_spi_isr().
> Remove spi-geni-qcom.h
> Remove inter words delay and CS to Clock toggle delay logic in the driver, as of now no clients are using it.
> Will submit this logic in the next patchset.
> Use major, minor and step macros to read from hardware version register.
>
> .../devicetree/bindings/soc/qcom/qcom,geni-se.txt | 2 -

Please split to a separate patch and explain why you are removing
spi-max-frequency?

> drivers/spi/Kconfig | 12 +
> drivers/spi/Makefile | 1 +
> drivers/spi/spi-geni-qcom.c | 678 +++++++++++++++++++++
> 4 files changed, 691 insertions(+), 2 deletions(-)
> create mode 100644 drivers/spi/spi-geni-qcom.c

\
 
 \ /
  Last update: 2018-08-29 02:26    [W:0.134 / U:0.188 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site