lkml.org 
[lkml]   [2018]   [Aug]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH V3] spi: spi-geni-qcom: Add SPI driver support for GENI based QUP
On 2018-08-29 05:55, Rob Herring wrote:
> On Fri, Aug 24, 2018 at 04:12:15PM +0530, Dilip Kota wrote:
>> From: Girish Mahadevan <girishm@codeaurora.org>
>>
>> This driver supports GENI based SPI Controller in the Qualcomm SOCs.
>> The
>> Qualcomm Generic Interface (GENI) is a programmable module supporting
>> a
>> wide range of serial interfaces including SPI. This driver supports
>> SPI
>> operations using FIFO mode of transfer.
>>
>> Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
>> Signed-off-by: Dilip Kota <dkota@codeaurora.org>
>> ---
>> Addressing all the reviewer commets given in Patchset1.
>> Summerizing all the comments below:
>>
>> MAKEFILE: Arrange SPI-GENI driver in alphabetical order
>> Kconfig: Mark SPI_GENI driver dependent on QCOM_GENI_SE
>> Enable SPI core auto runtime pm, and remove runtime pm calls.
>> Remove spi_geni_unprepare_message(),
>> spi_geni_unprepare_transfer_hardware()
>> Remove likely/unlikely keywords.
>> Remove get_spi_master() and use dev_get_drvdata()
>> Move request_irq to probe()
>> Mark bus number assignment to -1 as SPI core framework will assign
>> dynamically
>> Use devm_spi_register_master()
>> Include platform_device.h instead of of_platform.h
>> Removing macros which are used only once:
>> #define SPI_NUM_CHIPSELECT 4
>> #define SPI_XFER_TIMEOUT_MS 250
>> Place Register field definitions next to respective Register
>> definitions.
>> Replace int and u32 declerations to unsigned int.
>> Remove Hex numbers in debug prints.
>> Declare mode as u16 in spi_setup_word_len()
>> Remove the labels: setup_fifo_params_exit:
>> exit_prepare_transfer_hardware:
>> Declaring struct spi_master as spi everywhere in the file.
>> Calling spi_finalize_current_transfer() for end of transfer.
>> Hard code the SPI controller max frequency instead of reading from
>> DTSI node.
>> Spinlock not required, removed it.
>> Removed unrequired error prints.
>> Fix KASAN error in geni_spi_isr().
>> Remove spi-geni-qcom.h
>> Remove inter words delay and CS to Clock toggle delay logic in the
>> driver, as of now no clients are using it.
>> Will submit this logic in the next patchset.
>> Use major, minor and step macros to read from hardware version
>> register.
>>
>> .../devicetree/bindings/soc/qcom/qcom,geni-se.txt | 2 -
>
> Please split to a separate patch and explain why you are removing
> spi-max-frequency?

Hi Rob Herring,

In this patch, added changes for Driver not to read the SPI controller
Maximum frequency from the device tree. Accordingly I removed it in the
device tree documentation file. As both the files need to updated so did
in the same patch.
Could you please let me know the reason for making a separate patch.

--Dilip

>
>> drivers/spi/Kconfig | 12 +
>> drivers/spi/Makefile | 1 +
>> drivers/spi/spi-geni-qcom.c | 678
>> +++++++++++++++++++++
>> 4 files changed, 691 insertions(+), 2 deletions(-)
>> create mode 100644 drivers/spi/spi-geni-qcom.c

\
 
 \ /
  Last update: 2018-08-29 13:21    [W:0.151 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site