lkml.org 
[lkml]   [2018]   [Oct]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] ACPI: remove redundant 'default n' from Kconfig
Date
'default n' is the default value for any bool or tristate Kconfig
setting so there is no need to write it explicitly.

Also since commit f467c5640c29 ("kconfig: only write '# CONFIG_FOO
is not set' for visible symbols") the Kconfig behavior is the same
regardless of 'default n' being present or not:

...
One side effect of (and the main motivation for) this change is making
the following two definitions behave exactly the same:

config FOO
bool

config FOO
bool
default n

With this change, neither of these will generate a
'# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
That might make it clearer to people that a bare 'default n' is
redundant.
...

Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
---
drivers/acpi/Kconfig | 6 ------
1 file changed, 6 deletions(-)

Index: b/drivers/acpi/Kconfig
===================================================================
--- a/drivers/acpi/Kconfig 2018-09-26 15:54:31.942819766 +0200
+++ b/drivers/acpi/Kconfig 2018-10-10 16:38:09.691897907 +0200
@@ -138,7 +138,6 @@ config ACPI_REV_OVERRIDE_POSSIBLE

config ACPI_EC_DEBUGFS
tristate "EC read/write access through /sys/kernel/debug/ec"
- default n
help
Say N to disable Embedded Controller /sys/kernel/debug interface

@@ -283,7 +282,6 @@ config ACPI_PROCESSOR
config ACPI_IPMI
tristate "IPMI"
depends on IPMI_HANDLER
- default n
help
This driver enables the ACPI to access the BMC controller. And it
uses the IPMI request/response message to communicate with BMC
@@ -361,7 +359,6 @@ config ACPI_TABLE_UPGRADE

config ACPI_DEBUG
bool "Debug Statements"
- default n
help
The ACPI subsystem can produce debug output. Saying Y enables this
output and increases the kernel size by around 50K.
@@ -374,7 +371,6 @@ config ACPI_DEBUG
config ACPI_PCI_SLOT
bool "PCI slot detection driver"
depends on SYSFS
- default n
help
This driver creates entries in /sys/bus/pci/slots/ for all PCI
slots in the system. This can help correlate PCI bus addresses,
@@ -436,7 +432,6 @@ config ACPI_HED
config ACPI_CUSTOM_METHOD
tristate "Allow ACPI methods to be inserted/replaced at run time"
depends on DEBUG_FS
- default n
help
This debug facility allows ACPI AML methods to be inserted and/or
replaced without rebooting the system. For details refer to:
@@ -481,7 +476,6 @@ config ACPI_EXTLOG
tristate "Extended Error Log support"
depends on X86_MCE && X86_LOCAL_APIC && EDAC
select UEFI_CPER
- default n
help
Certain usages such as Predictive Failure Analysis (PFA) require
more information about the error than what can be described in
\
 
 \ /
  Last update: 2018-10-10 16:41    [W:0.041 / U:0.104 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site