lkml.org 
[lkml]   [2018]   [Jan]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 10/16] iio: adc: sun4i-gpadc-iio: add support for A83T thermal sensor
From
Date


On 29.01.2018 10:48, Maxime Ripard wrote:
> On Mon, Jan 29, 2018 at 12:29:13AM +0100, Philipp Rossak wrote:
>> This patch adds support for the A83T ths sensor.
>>
>> The A83T supports interrupts. The interrupt is configured to update the
>> the sensor values every second.
>>
>> Signed-off-by: Philipp Rossak <embed3d@gmail.com>
>> ---
>> drivers/iio/adc/sun4i-gpadc-iio.c | 38 ++++++++++++++++++++++++++++++++++++++
>> include/linux/mfd/sun4i-gpadc.h | 18 ++++++++++++++++++
>> 2 files changed, 56 insertions(+)
>>
>> diff --git a/drivers/iio/adc/sun4i-gpadc-iio.c b/drivers/iio/adc/sun4i-gpadc-iio.c
>> index 8196203d65fe..9f7895ba1966 100644
>> --- a/drivers/iio/adc/sun4i-gpadc-iio.c
>> +++ b/drivers/iio/adc/sun4i-gpadc-iio.c
>> @@ -170,6 +170,40 @@ static const struct gpadc_data sun8i_h3_ths_data = {
>> SUN8I_H3_THS_TEMP_PERIOD(0x7),
>> };
>>
>> +static const struct gpadc_data sun8i_a83t_ths_data = {
>> + .temp_offset = -2724,
>> + .temp_scale = -70,
>> + .temp_data = {SUN8I_H3_THS_TDATA0,
>> + SUN8I_A83T_THS_TDATA1,
>> + SUN8I_A83T_THS_TDATA2,
>> + 0},
>> + .sample_start = sunxi_ths_sample_start,
>> + .sample_end = sunxi_ths_sample_end,
>> + .sensor_count = 3,
>> + .supports_nvmem = false,
>> + .support_irq = true,
>> + .ctrl0_map = SUN4I_GPADC_CTRL0_T_ACQ(0x1f3),
>> + .ctrl2_map = SUN8I_H3_THS_ACQ1(0x1f3),
>
> Where are these values coming from?
>

These values are calculated with the formulas from the datasheet and
also tested on hardware. These settings seem ok.

>> + .sensor_en_map = SUN8I_H3_THS_TEMP_SENSE_EN0 |
>> + SUN8I_A83T_THS_TEMP_SENSE_EN1 |
>> + SUN8I_A83T_THS_TEMP_SENSE_EN2,
>> + .filter_map = SUN4I_GPADC_CTRL3_FILTER_EN |
>> + SUN4I_GPADC_CTRL3_FILTER_TYPE(0x2),
>> + .irq_clear_map = SUN8I_H3_THS_INTS_ALARM_INT_0 |
>> + SUN8I_A83T_THS_INTS_ALARM_INT_1 |
>> + SUN8I_A83T_THS_INTS_ALARM_INT_2 |
>> + SUN8I_H3_THS_INTS_SHUT_INT_0 |
>> + SUN8I_A83T_THS_INTS_SHUT_INT_1 |
>> + SUN8I_A83T_THS_INTS_SHUT_INT_2 |
>> + SUN8I_H3_THS_INTS_TDATA_IRQ_0 |
>> + SUN8I_A83T_THS_INTS_TDATA_IRQ_1 |
>> + SUN8I_A83T_THS_INTS_TDATA_IRQ_2,
>
> Do you reall need to clear all these interrupts if you're using only
> one?
>

No, I don't think so, I will remove them in the next version.

> Maxime
>

Philipp

\
 
 \ /
  Last update: 2018-01-29 12:56    [W:0.059 / U:0.168 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site