lkml.org 
[lkml]   [2017]   [Jun]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/2] spi: rockchip: add support for "cs-gpios" dts property
Hi Shawn,

On 06/12/2017 04:26 PM, jeffy wrote:
> Hi Shawn,
>
> On 06/12/2017 03:15 PM, Shawn Lin wrote:
>> Hi Jeffy,
>>
>> On 2017/6/12 14:14, Jeffy Chen wrote:
>>> Support using "cs-gpios" property to specify cs gpios.
>>>
>>> Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
>>> ---
>>>
>>> .../devicetree/bindings/spi/spi-rockchip.txt | 2 +
>>> drivers/spi/spi-rockchip.c | 52
>>> ++++++++++++++++++++++
>>> 2 files changed, 54 insertions(+)
>>>
>>> diff --git a/Documentation/devicetree/bindings/spi/spi-rockchip.txt
>>> b/Documentation/devicetree/bindings/spi/spi-rockchip.txt
>>> index 83da493..02171b2 100644
>>> --- a/Documentation/devicetree/bindings/spi/spi-rockchip.txt
>>> +++ b/Documentation/devicetree/bindings/spi/spi-rockchip.txt
>>
>> The changes for doc should be another patch, and...
>
> but i saw others didn't separate them:
> cf9e478 spi: sh-msiof: Add slave mode support
> 23e291c spi: rockchip: support "sleep" pin configuration
>
>
>>
>>> @@ -17,6 +17,7 @@ Required Properties:
>>> region.
>>> - interrupts: The interrupt number to the cpu. The interrupt
>>> specifier format
>>> depends on the interrupt controller.
>>> +- cs-gpios : Specifies the gpio pins to be used for chipselects.
>>
>> It's not a required property, otherwise how other boards work as your
>> patch 2 only add this for rk3399-gru.
> oops, i will fix it.
>>
>>> - clocks: Must contain an entry for each entry in clock-names.
>>> - clock-names: Shall be "spiclk" for the transfer-clock, and
>>> "apb_pclk" for
>>> the peripheral clock.
>>> @@ -48,6 +49,7 @@ Example:
>>> #address-cells = <1>;
>>> #size-cells = <0>;
>>> interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
>>> + cs-gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;
>>> clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>;
>>> clock-names = "spiclk", "apb_pclk";
>>> pinctrl-0 = <&spi1_pins>;
>>> diff --git a/drivers/spi/spi-rockchip.c b/drivers/spi/spi-rockchip.c
>>> index acf31f3..04694e1 100644
>>> --- a/drivers/spi/spi-rockchip.c
>>> +++ b/drivers/spi/spi-rockchip.c
>>> @@ -15,6 +15,7 @@
>>> #include <linux/clk.h>
>>> #include <linux/dmaengine.h>
>>> +#include <linux/gpio.h>
>>> #include <linux/module.h>
>>> #include <linux/of.h>
>>> #include <linux/pinctrl/consumer.h>
>>> @@ -201,6 +202,10 @@ struct rockchip_spi {
>>> struct dma_slave_caps dma_caps;
>>> };
>>> +struct rockchip_spi_data {
>>> + bool cs_gpio_requested;
>>> +};
>>> +
>>
>> Could you fold cs_gpio_requested into struct rockchip_spi?
we might have multiple children with different cs_gpio, so i think we
may need a separate data struct for them.
>>
>>> static inline void spi_enable_chip(struct rockchip_spi *rs, int
>>> enable)
>>> {
>>> writel_relaxed((enable ? 1 : 0), rs->regs + ROCKCHIP_SPI_SSIENR);
>>> @@ -297,6 +302,50 @@ static void rockchip_spi_set_cs(struct spi_device
>>> *spi, bool enable)
>>> pm_runtime_put_sync(rs->dev);
>>> }
>>> +static int rockchip_spi_setup(struct spi_device *spi)
>>> +{
>>> + int ret = 0;
>>> + unsigned long flags = (spi->mode & SPI_CS_HIGH) ?
>>> + GPIOF_OUT_INIT_LOW : GPIOF_OUT_INIT_HIGH;
>>> + struct rockchip_spi_data *data = spi_get_ctldata(spi);
>>> +
>>> + if (!gpio_is_valid(spi->cs_gpio))
>>> + return 0;
>>
>> return -EINVAL?
> i think we can still support the original way, which means no "cs-gpios"
> and do nothing in setup.
>>
>>> +
>>> + if (!data) {
>>> + data = kzalloc(sizeof(*data), GFP_KERNEL);
>>> + if (!data)
>>> + return -ENOMEM;
>>> + spi_set_ctldata(spi, data);
>>> + }
>>> +
>>> + if (!data->cs_gpio_requested) {
>>> + ret = gpio_request_one(spi->cs_gpio, flags,
>>> + dev_name(&spi->dev));
>>> + if (!ret)
>>> + data->cs_gpio_requested = 1;
>>> + } else
>>> + ret = gpio_direction_output(spi->cs_gpio, flags);
>>
>> need brace around 'else' statement. Also I don't see data used
>> elsewhere, so you need these code above.
> ok.
> and the cs_gpio_requested is to mark cs_gpio requested, because the
> setup func might be called multiple times, we only need to request gpio
> at the first time.
>>
>>> +
>>> + if (ret < 0)
>>> + dev_err(&spi->dev, "Failed to setup cs gpio(%d): %d\n",
>>> + spi->cs_gpio, ret);
>>> +
>>> + return ret;
>>> +}
>>> +
>>> +static void rockchip_spi_cleanup(struct spi_device *spi)
>>> +{
>>> + struct rockchip_spi_data *data = spi_get_ctldata(spi);
>>> +
>>> + if (data) {
>>> + if (data->cs_gpio_requested)
>>> + gpio_free(spi->cs_gpio);
>>> + kfree(data);
>>> + spi_set_ctldata(spi, NULL);
>>> + }
>>> +}
>>> +
>>> static int rockchip_spi_prepare_message(struct spi_master *master,
>>> struct spi_message *msg)
>>> {
>>> @@ -744,11 +793,14 @@ static int rockchip_spi_probe(struct
>>> platform_device *pdev)
>>> master->bits_per_word_mask = SPI_BPW_MASK(16) | SPI_BPW_MASK(8);
>>> master->set_cs = rockchip_spi_set_cs;
>>> + master->setup = rockchip_spi_setup;
>>> + master->cleanup = rockchip_spi_cleanup;
>>> master->prepare_message = rockchip_spi_prepare_message;
>>> master->unprepare_message = rockchip_spi_unprepare_message;
>>> master->transfer_one = rockchip_spi_transfer_one;
>>> master->max_transfer_size = rockchip_spi_max_transfer_size;
>>> master->handle_err = rockchip_spi_handle_err;
>>> + master->flags = SPI_MASTER_GPIO_SS;
>>> rs->dma_tx.ch = dma_request_chan(rs->dev, "tx");
>>> if (IS_ERR(rs->dma_tx.ch)) {
>>>
>>
>>
>>
>


\
 
 \ /
  Last update: 2017-06-12 10:35    [W:0.092 / U:1.148 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site