lkml.org 
[lkml]   [2015]   [Aug]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH-v2 2/2] regulator: 88pm800: Add support for configuration of dual phase on BUCK1


On Thursday 23 July 2015 10:21 AM, Krzysztof Kozlowski wrote:
> 2015-07-22 1:23 GMT+09:00 Vaibhav Hiremath <vaibhav.hiremath@linaro.org>:
>> 88PM860 device supports dual phase mode on BUCK1 output.
>> In normal usecase, BUCK1A and BUCK1B operates independently with 3A
>> capacity. And they both can work as a dual phase providing 6A capacity.
>>
>> This patch updates the regulator driver to read the respective
>> DT property and enable dual-phase mode on BUCK1.
>>
>> Note that, this is init time (one time) initialization.
>>

Sorry for delayed response, was on bed rest almost for week.

>> Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
>> ---
>> drivers/regulator/88pm800.c | 31 +++++++++++++++++++++++++++++++
>> include/linux/mfd/88pm80x.h | 3 +++
>> 2 files changed, 34 insertions(+)
>
> Don't you need to update the constraints also? I think the BUCK1
> regulator has fixed constraint of 3 A:
> PM800_BUCK(buck1, BUCK1, BUCK_ENA, 0, 3000000, buck1_volt_range, 0x55),
> and now it can handle 6 A.
>

Actually, BUCK1A and BUCK1B both combined together provide 6A capacity.
And as discussed earlier, we need board change for this.

I am quite not sure.

Should I read the property and update the constraint runtime during
probe?


>>
>> diff --git a/drivers/regulator/88pm800.c b/drivers/regulator/88pm800.c
>> index e846e4c..1bf2b35 100644
>> --- a/drivers/regulator/88pm800.c
>> +++ b/drivers/regulator/88pm800.c
>> @@ -267,6 +267,31 @@ static struct pm800_regulator_info pm860_regulator_info[] = {
>> PM800_LDO(ldo20, LDO20, LDO_ENA1_3, 3, 10000, ldo_volt_table2),
>> };
>>
>> +static int pm800_regulator_init(struct platform_device *pdev)
>> +{
>> + struct pm800_regulators *pm800_data = platform_get_drvdata(pdev);
>> + struct pm80x_chip *chip = pm800_data->chip;
>> + int ret;
>
> 'ret' is used only in if statement below. I don't have strong feelings
> but can you move it there to limit its scope or always return 'ret'
> (after initializing to '0'). To me this would be more readable.
>

OK, will fix in V3.

I will wait to close on constraint discussion above.

Thanks,
Vaibhav

> Best regards,
> Krzysztof
>
>> +
>> + /* Currently only supported on 88pm860 device */
>> + if (chip->type != CHIP_PM860)
>> + return 0;
>> +
>> + if (of_property_read_bool(pdev->dev.of_node,
>> + "marvell,88pm860-buck1-dualphase-en")) {
>> + ret = regmap_update_bits(chip->subchip->regmap_power,
>> + PM860_BUCK1_MISC,
>> + BUCK1_DUAL_PHASE_SEL,
>> + BUCK1_DUAL_PHASE_SEL);
>> + if (ret) {
>> + dev_err(chip->dev, "failed to set dual-pase mode %d\n", ret);
>> + return ret;
>> + }
>> + }
>> +
>> + return 0;
>> +}
>> +
>> static int pm800_regulator_probe(struct platform_device *pdev)
>> {
>> struct pm80x_chip *chip = dev_get_drvdata(pdev->dev.parent);
>> @@ -336,6 +361,12 @@ static int pm800_regulator_probe(struct platform_device *pdev)
>> }
>> }
>>
>> + ret = pm800_regulator_init(pdev);
>> + if (ret) {
>> + dev_err(&pdev->dev, "failed to init 88pm800 regulator device\n");
>> + return ret;
>> + }
>> +
>> return 0;
>> }
>>
>> diff --git a/include/linux/mfd/88pm80x.h b/include/linux/mfd/88pm80x.h
>> index a92d173..05d9bad 100644
>> --- a/include/linux/mfd/88pm80x.h
>> +++ b/include/linux/mfd/88pm80x.h
>> @@ -295,6 +295,9 @@ enum {
>> #define PM860_BUCK4_MISC2 (0x82)
>> #define PM860_BUCK4_FULL_DRV BIT(2)
>>
>> +#define PM860_BUCK1_MISC (0x8E)
>> +#define BUCK1_DUAL_PHASE_SEL BIT(2)
>> +
>> struct pm80x_rtc_pdata {
>> int vrtc;
>> int rtc_wakeup;
>> --
>> 1.9.1
>>
>>
>> _______________________________________________
>> linux-arm-kernel mailing list
>> linux-arm-kernel@lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel


\
 
 \ /
  Last update: 2015-08-05 11:01    [W:0.159 / U:0.248 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site