lkml.org 
[lkml]   [2015]   [Jul]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH-v2 2/2] regulator: 88pm800: Add support for configuration of dual phase on BUCK1
Date
88PM860 device supports dual phase mode on BUCK1 output.
In normal usecase, BUCK1A and BUCK1B operates independently with 3A
capacity. And they both can work as a dual phase providing 6A capacity.

This patch updates the regulator driver to read the respective
DT property and enable dual-phase mode on BUCK1.

Note that, this is init time (one time) initialization.

Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
---
drivers/regulator/88pm800.c | 31 +++++++++++++++++++++++++++++++
include/linux/mfd/88pm80x.h | 3 +++
2 files changed, 34 insertions(+)

diff --git a/drivers/regulator/88pm800.c b/drivers/regulator/88pm800.c
index e846e4c..1bf2b35 100644
--- a/drivers/regulator/88pm800.c
+++ b/drivers/regulator/88pm800.c
@@ -267,6 +267,31 @@ static struct pm800_regulator_info pm860_regulator_info[] = {
PM800_LDO(ldo20, LDO20, LDO_ENA1_3, 3, 10000, ldo_volt_table2),
};

+static int pm800_regulator_init(struct platform_device *pdev)
+{
+ struct pm800_regulators *pm800_data = platform_get_drvdata(pdev);
+ struct pm80x_chip *chip = pm800_data->chip;
+ int ret;
+
+ /* Currently only supported on 88pm860 device */
+ if (chip->type != CHIP_PM860)
+ return 0;
+
+ if (of_property_read_bool(pdev->dev.of_node,
+ "marvell,88pm860-buck1-dualphase-en")) {
+ ret = regmap_update_bits(chip->subchip->regmap_power,
+ PM860_BUCK1_MISC,
+ BUCK1_DUAL_PHASE_SEL,
+ BUCK1_DUAL_PHASE_SEL);
+ if (ret) {
+ dev_err(chip->dev, "failed to set dual-pase mode %d\n", ret);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
static int pm800_regulator_probe(struct platform_device *pdev)
{
struct pm80x_chip *chip = dev_get_drvdata(pdev->dev.parent);
@@ -336,6 +361,12 @@ static int pm800_regulator_probe(struct platform_device *pdev)
}
}

+ ret = pm800_regulator_init(pdev);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to init 88pm800 regulator device\n");
+ return ret;
+ }
+
return 0;
}

diff --git a/include/linux/mfd/88pm80x.h b/include/linux/mfd/88pm80x.h
index a92d173..05d9bad 100644
--- a/include/linux/mfd/88pm80x.h
+++ b/include/linux/mfd/88pm80x.h
@@ -295,6 +295,9 @@ enum {
#define PM860_BUCK4_MISC2 (0x82)
#define PM860_BUCK4_FULL_DRV BIT(2)

+#define PM860_BUCK1_MISC (0x8E)
+#define BUCK1_DUAL_PHASE_SEL BIT(2)
+
struct pm80x_rtc_pdata {
int vrtc;
int rtc_wakeup;
--
1.9.1


\
 
 \ /
  Last update: 2015-07-21 18:41    [W:0.210 / U:0.172 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site