lkml.org 
[lkml]   [2015]   [Aug]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Subject[PATCH linux-next v5 0/5] add driver for Atmel QSPI controller
Date
ChangeLog

v5:
- remove unused inline functions qspi_read[bw]() and qspi_write[bw](),
keep only qspi_readl() and qspi_writel().
- use reinit_completion() instead of init_completion() during run time,
call init_completion() once for all in the probe().
- add a dev_warn() when trying to tune the number of dummy cycles for
spi-nor of a not supported manufacturer then fall back to the default
framework value.
- reword some comments.
- add "Acked-by: Marek Vasut <marex@denx.de>" for patches 1 and 4.
- add "Acked-by: Bean Huo <beanhuo@micron.com>" for patch 1.

v4:
- add "OF && HAS_DMA" dependency in Kconfig for Atmel Quad SPI driver.
- return -ENOMEM instead of the return code of dma_mapping_error() as this
function returns a boolean on ARM achitecture.
- add "Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>" for Atmel Quad
SPI driver and its DT binding documentation.

v3:
- reword the comment which explains that spi_nor_set_protocol() is used by
the spi-nor framework to notify lower layers, especially the (Q)SPI
controller about a protocol change.
- change the definitions of register/bitfield macros in the Atmel QSPI
controller driver: get rid of concatenation operator and use BIT and
GENMASK macros when possible.
- use #define[SPACE] instead of #define[TAB]

v2:
- remove the patches to set the "latency code" of Spansion QSPI memories
(support of Spansion memories may be submitted in later series).
- rename "qspi" node into "spi" in the DT example to fit ePAPR standard.
- remove the useless "qspi0" label from the DT node example.
- remove the leading 0 from the size of the second memory region to make
it consistent with the size of the first memory region.
- indent the DT bindings documentation to make it more readable.
- remove the useless ".bus = &platform_bus_type," line from the
platform driver definition.

v1:

This series of patches add support for the new Atmel QSPI controller
embedded inside sama5d2x SoCs.

These patches were first developped for linux-3.18-at91 and tested on a
sama5d27 Xplained ultra board, which embeds a Micron n25q128a13 QSPI NOR
flash memory. Then the series was adapted for mainline.

Cyrille Pitchen (5):
mtd: spi-nor: notify (Q)SPI controller about protocol change
Documentation: mtd: add a DT property to set the number of dummy
cycles
mtd: spi-nor: allow to tune the number of dummy cycles
Documentation: atmel-quadspi: add binding file for Atmel QSPI driver
mtd: atmel-quadspi: add driver for Atmel QSPI controller

.../devicetree/bindings/mtd/atmel-quadspi.txt | 29 +
.../devicetree/bindings/mtd/jedec,spi-nor.txt | 6 +
drivers/mtd/spi-nor/Kconfig | 7 +
drivers/mtd/spi-nor/Makefile | 1 +
drivers/mtd/spi-nor/atmel-quadspi.c | 859 +++++++++++++++++++++
drivers/mtd/spi-nor/spi-nor.c | 123 ++-
include/linux/mtd/spi-nor.h | 15 +
7 files changed, 1021 insertions(+), 19 deletions(-)
create mode 100644 Documentation/devicetree/bindings/mtd/atmel-quadspi.txt
create mode 100644 drivers/mtd/spi-nor/atmel-quadspi.c

--
1.8.2.2



\
 
 \ /
  Last update: 2015-08-26 14:41    [W:0.605 / U:0.016 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site