lkml.org 
[lkml]   [2015]   [Jan]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH/RFC v10 02/19] Documentation: leds: Add description of LED Flash class extension
Date
The documentation being added contains overall description of the
LED Flash Class and the related sysfs attributes.

Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
---
Documentation/leds/leds-class-flash.txt | 57 +++++++++++++++++++++++++++++++
1 file changed, 57 insertions(+)
create mode 100644 Documentation/leds/leds-class-flash.txt

diff --git a/Documentation/leds/leds-class-flash.txt b/Documentation/leds/leds-class-flash.txt
new file mode 100644
index 0000000..d80096b
--- /dev/null
+++ b/Documentation/leds/leds-class-flash.txt
@@ -0,0 +1,57 @@
+
+Flash LED handling under Linux
+==============================
+
+Some LED devices support two modes - torch and flash. In the LED subsystem
+those modes are supported by LED class (see Documentation/leds/leds-class.txt)
+and LED Flash class respectively. The torch mode related features are enabled
+by default and the flash ones only if a driver declares it by setting
+LED_DEV_CAP_FLASH flag.
+
+In order to enable support for flash LEDs CONFIG_LEDS_CLASS_FLASH symbol
+must be defined in the kernel config. A flash LED driver must register
+in the LED subsystem with led_classdev_flash_register function to gain flash
+related capabilities.
+
+There are flash LED devices which can control more than one LED and allow for
+strobing the sub-leds synchronously. A LED will be strobed synchronously with
+the one whose identifier is written to the flash_sync_strobe sysfs attribute.
+The list of available sub-led identifiers can be read from the available_sync_leds
+sysfs attribute. In order to enable the related settings the driver must set
+LED_DEV_CAP_SYNC_STROBE flag.
+
+Following sysfs attributes are exposed for controlling flash led devices:
+
+ - flash_brightness - flash LED brightness in microamperes (RW)
+ - max_flash_brightness - maximum available flash LED brightness (RO)
+ - flash_timeout - flash strobe duration in microseconds (RW)
+ - max_flash_timeout - maximum available flash strobe duration (RO)
+ - flash_strobe - flash strobe state (RW)
+ - available_sync_leds - list of sub-leds available for flash strobe
+ synchronization (RO)
+ - flash_sync_strobe - identifier of the sub-led to synchronize the flash
+ strobe with; 0 stands for no synchronization (RW)
+ - flash_fault - bitmask of flash faults that may have occurred
+ possible flags are:
+ * 0x01 - flash controller voltage to the flash LED has exceeded
+ the limit specific to the flash controller
+ * 0x02 - the flash strobe was still on when the timeout set by
+ the user has expired; not all flash controllers may
+ set this in all such conditions
+ * 0x04 - the flash controller has overheated
+ * 0x08 - the short circuit protection of the flash controller
+ has been triggered
+ * 0x10 - current in the LED power supply has exceeded the limit
+ specific to the flash controller
+ * 0x20 - the flash controller has detected a short or open
+ circuit condition on the indicator LED
+ * 0x40 - flash controller voltage to the flash LED has been
+ below the minimum limit specific to the flash
+ * 0x80 - the input voltage of the flash controller is below
+ the limit under which strobing the flash at full
+ current will not be possible. The condition persists
+ until this flag is no longer set
+ * 0x100 - the temperature of the LED has exceeded its allowed
+ upper limit
+
+ Flash faults are cleared, if possible, by reading the attribute.
--
1.7.9.5


\
 
 \ /
  Last update: 2015-01-09 16:41    [W:0.588 / U:0.292 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site