lkml.org 
[lkml]   [2015]   [Jan]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2] hwmon: (ina2xx) Add ina231 compatible string
Date
From: Kevin Hilman <khilman@linaro.org>

Add support for "ina231" as compatible string, and update
Documentation and Kconfig accordingly.

Tested with the Exynos5422-based odroid-xu3 board which has on-board
INA231 sensors.

Signed-off-by: Kevin Hilman <khilman@linaro.org>
---
Documentation/hwmon/ina2xx | 9 +++++++++
drivers/hwmon/Kconfig | 4 ++--
drivers/hwmon/ina2xx.c | 1 +
3 files changed, 12 insertions(+), 2 deletions(-)

diff --git a/Documentation/hwmon/ina2xx b/Documentation/hwmon/ina2xx
index 4223c2d3b508..c2f838f65ee4 100644
--- a/Documentation/hwmon/ina2xx
+++ b/Documentation/hwmon/ina2xx
@@ -26,6 +26,12 @@ Supported chips:
Datasheet: Publicly available at the Texas Instruments website
http://www.ti.com/

+ * Texas Instruments INA231
+ Prefix: 'ina231'
+ Addresses: I2C 0x40 - 0x4f
+ Datasheet: Publicly available at the Texas Instruments website
+ http://www.ti.com/
+
Author: Lothar Felten <l-felten@ti.com>

Description
@@ -44,6 +50,9 @@ The INA226 monitors both a shunt voltage drop and bus supply voltage.
The INA230 is a high or low side current shunt and power monitor with an I2C
interface. The INA230 monitors both a shunt voltage drop and bus supply voltage.

+The INA231 is a high or low side current shunt and power monitor with an I2C
+interface. The INA230 monitors both a shunt voltage drop and bus supply voltage.
+
The shunt value in micro-ohms can be set via platform data or device tree.
Please refer to the Documentation/devicetree/bindings/i2c/ina2xx.txt for bindings
if the device tree is used.
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 6529c09c46f0..408fb6f5f055 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -1420,8 +1420,8 @@ config SENSORS_INA2XX
tristate "Texas Instruments INA219 and compatibles"
depends on I2C
help
- If you say yes here you get support for INA219, INA220, INA226, and
- INA230 power monitor chips.
+ If you say yes here you get support for INA219, INA220, INA226,
+ INA230, and INA231 power monitor chips.

The INA2xx driver is configured for the default configuration of
the part as described in the datasheet.
diff --git a/drivers/hwmon/ina2xx.c b/drivers/hwmon/ina2xx.c
index e01feba909c3..8c4a29bd2eaf 100644
--- a/drivers/hwmon/ina2xx.c
+++ b/drivers/hwmon/ina2xx.c
@@ -287,6 +287,7 @@ static const struct i2c_device_id ina2xx_id[] = {
{ "ina220", ina219 },
{ "ina226", ina226 },
{ "ina230", ina226 },
+ { "ina231", ina226 },
{ }
};
MODULE_DEVICE_TABLE(i2c, ina2xx_id);
--
2.1.3


\
 
 \ /
  Last update: 2015-01-15 02:41    [W:0.063 / U:0.008 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site