lkml.org 
[lkml]   [2014]   [Jul]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 1/2] net: davinci_mdio: reuse for keystone2 arch
Date
The similar MDIO HW blocks is used by keystone 2 SoCs as
in Davinci SoCs:
- one in Gigabit Ethernet (GbE) Switch Subsystem
See http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf
- one in 10 Gigabit Ethernet Subsystem
See http://www.ti.com/lit/ug/spruhj5/spruhj5.pdf

Hence, reuse Davinci MDIO driver for Keystone 2 and
enable TI networking for Keystone 2 devices

Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
.../devicetree/bindings/net/davinci-mdio.txt | 8 ++++----
drivers/net/ethernet/ti/Kconfig | 4 ++--
2 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/davinci-mdio.txt b/Documentation/devicetree/bindings/net/davinci-mdio.txt
index 72efaaf..0369e25 100644
--- a/Documentation/devicetree/bindings/net/davinci-mdio.txt
+++ b/Documentation/devicetree/bindings/net/davinci-mdio.txt
@@ -1,8 +1,8 @@
-TI SoC Davinci MDIO Controller Device Tree Bindings
+TI SoC Davinci/Keystone2 MDIO Controller Device Tree Bindings
---------------------------------------------------

Required properties:
-- compatible : Should be "ti,davinci_mdio"
+- compatible : Should be "ti,davinci_mdio" or "ti,keystone_mdio"
- reg : physical base address and size of the davinci mdio
registers map
- bus_freq : Mdio Bus frequency
@@ -19,7 +19,7 @@ file.
Examples:

mdio: davinci_mdio@4A101000 {
- compatible = "ti,cpsw";
+ compatible = "ti,davinci_mdio";
reg = <0x4A101000 0x1000>;
bus_freq = <1000000>;
};
@@ -27,7 +27,7 @@ Examples:
(or)

mdio: davinci_mdio@4A101000 {
- compatible = "ti,cpsw";
+ compatible = "ti,davinci_mdio";
ti,hwmods = "davinci_mdio";
bus_freq = <1000000>;
};
diff --git a/drivers/net/ethernet/ti/Kconfig b/drivers/net/ethernet/ti/Kconfig
index 53150c2..1769700 100644
--- a/drivers/net/ethernet/ti/Kconfig
+++ b/drivers/net/ethernet/ti/Kconfig
@@ -5,7 +5,7 @@
config NET_VENDOR_TI
bool "Texas Instruments (TI) devices"
default y
- depends on PCI || EISA || AR7 || (ARM && (ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX))
+ depends on PCI || EISA || AR7 || (ARM && (ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX || ARCH_KEYSTONE))
---help---
If you have a network (Ethernet) card belonging to this class, say Y
and read the Ethernet-HOWTO, available from
@@ -32,7 +32,7 @@ config TI_DAVINCI_EMAC

config TI_DAVINCI_MDIO
tristate "TI DaVinci MDIO Support"
- depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX )
+ depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX || ARCH_KEYSTONE )
select PHYLIB
---help---
This driver supports TI's DaVinci MDIO module.
--
1.7.9.5


\
 
 \ /
  Last update: 2014-07-16 14:01    [W:0.059 / U:0.972 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site