lkml.org 
[lkml]   [2014]   [Mar]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 02/13] phy: omap-control: Update DT binding information
Date
Move omap-control binding information to the right location.

Signed-off-by: Roger Quadros <rogerq@ti.com>
---
Documentation/devicetree/bindings/phy/ti-phy.txt | 25 ++++++++++++++++++++++
Documentation/devicetree/bindings/usb/omap-usb.txt | 24 ---------------------
2 files changed, 25 insertions(+), 24 deletions(-)

diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt
index f671163..5c5b1b0 100644
--- a/Documentation/devicetree/bindings/phy/ti-phy.txt
+++ b/Documentation/devicetree/bindings/phy/ti-phy.txt
@@ -1,5 +1,30 @@
TI PHY: DT DOCUMENTATION FOR PHYs in TI PLATFORMs

+OMAP CONTROL PHY
+
+Required properties:
+ - compatible: Should be one of
+ "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4.
+ "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register
+ e.g. USB2_PHY on OMAP5.
+ "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control
+ e.g. USB3 PHY and SATA PHY on OMAP5.
+ "ti,control-phy-dra7usb2" - if it has power down register like USB2 PHY on
+ DRA7 platform.
+ "ti,control-phy-am437usb2" - if it has power down register like USB2 PHY on
+ AM437 platform.
+ - reg : Address and length of the register set for the device. It contains
+ the address of "otghs_control" for control-phy-otghs or "power" register
+ for other types.
+ - reg-names: should be "otghs_control" control-phy-otghs and "power" for
+ other types.
+
+omap_control_usb: omap-control-usb@4a002300 {
+ compatible = "ti,control-phy-otghs";
+ reg = <0x4a00233c 0x4>;
+ reg-names = "otghs_control";
+};
+
OMAP USB2 PHY

Required properties:
diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
index c495135..38b2fae 100644
--- a/Documentation/devicetree/bindings/usb/omap-usb.txt
+++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
@@ -76,27 +76,3 @@ omap_dwc3 {
ranges;
};

-OMAP CONTROL USB
-
-Required properties:
- - compatible: Should be one of
- "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4.
- "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register
- e.g. USB2_PHY on OMAP5.
- "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control
- e.g. USB3 PHY and SATA PHY on OMAP5.
- "ti,control-phy-dra7usb2" - if it has power down register like USB2 PHY on
- DRA7 platform.
- "ti,control-phy-am437usb2" - if it has power down register like USB2 PHY on
- AM437 platform.
- - reg : Address and length of the register set for the device. It contains
- the address of "otghs_control" for control-phy-otghs or "power" register
- for other types.
- - reg-names: should be "otghs_control" control-phy-otghs and "power" for
- other types.
-
-omap_control_usb: omap-control-usb@4a002300 {
- compatible = "ti,control-phy-otghs";
- reg = <0x4a00233c 0x4>;
- reg-names = "otghs_control";
-};
--
1.8.3.2


\
 
 \ /
  Last update: 2014-03-09 16:44    [W:1.556 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site