lkml.org 
[lkml]   [2014]   [Mar]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 02/13] phy: omap-control: Update DT binding information
Felipe,

On Thursday 06 March 2014 08:08 PM, Roger Quadros wrote:
> Move omap-control binding information to the right location.
>
> Signed-off-by: Roger Quadros <rogerq@ti.com>
> ---
> Documentation/devicetree/bindings/phy/ti-phy.txt | 25 ++++++++++++++++++++++

This patch is dependent on

"Documentation: dt bindings: move ..usb/usb-phy.txt to
..phy/ti-phy.txt"

which got merged in your tree. So can you take this patch also?
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>

Regards
Kishon

> Documentation/devicetree/bindings/usb/omap-usb.txt | 24 ---------------------
> 2 files changed, 25 insertions(+), 24 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt
> index f671163..5c5b1b0 100644
> --- a/Documentation/devicetree/bindings/phy/ti-phy.txt
> +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt
> @@ -1,5 +1,30 @@
> TI PHY: DT DOCUMENTATION FOR PHYs in TI PLATFORMs
>
> +OMAP CONTROL PHY
> +
> +Required properties:
> + - compatible: Should be one of
> + "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4.
> + "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register
> + e.g. USB2_PHY on OMAP5.
> + "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control
> + e.g. USB3 PHY and SATA PHY on OMAP5.
> + "ti,control-phy-dra7usb2" - if it has power down register like USB2 PHY on
> + DRA7 platform.
> + "ti,control-phy-am437usb2" - if it has power down register like USB2 PHY on
> + AM437 platform.
> + - reg : Address and length of the register set for the device. It contains
> + the address of "otghs_control" for control-phy-otghs or "power" register
> + for other types.
> + - reg-names: should be "otghs_control" control-phy-otghs and "power" for
> + other types.
> +
> +omap_control_usb: omap-control-usb@4a002300 {
> + compatible = "ti,control-phy-otghs";
> + reg = <0x4a00233c 0x4>;
> + reg-names = "otghs_control";
> +};
> +
> OMAP USB2 PHY
>
> Required properties:
> diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
> index c495135..38b2fae 100644
> --- a/Documentation/devicetree/bindings/usb/omap-usb.txt
> +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
> @@ -76,27 +76,3 @@ omap_dwc3 {
> ranges;
> };
>
> -OMAP CONTROL USB
> -
> -Required properties:
> - - compatible: Should be one of
> - "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4.
> - "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register
> - e.g. USB2_PHY on OMAP5.
> - "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control
> - e.g. USB3 PHY and SATA PHY on OMAP5.
> - "ti,control-phy-dra7usb2" - if it has power down register like USB2 PHY on
> - DRA7 platform.
> - "ti,control-phy-am437usb2" - if it has power down register like USB2 PHY on
> - AM437 platform.
> - - reg : Address and length of the register set for the device. It contains
> - the address of "otghs_control" for control-phy-otghs or "power" register
> - for other types.
> - - reg-names: should be "otghs_control" control-phy-otghs and "power" for
> - other types.
> -
> -omap_control_usb: omap-control-usb@4a002300 {
> - compatible = "ti,control-phy-otghs";
> - reg = <0x4a00233c 0x4>;
> - reg-names = "otghs_control";
> -};
>


\
 
 \ /
  Last update: 2014-03-06 17:21    [W:1.862 / U:0.308 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site