lkml.org 
[lkml]   [2014]   [Feb]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] usb: gadget: s3c-hsotg: fix build on x86 and other architectures
Date
The readsl and writesl I/O accessors are only defined on some
architectures. The driver currently depends on CONFIG_ARM because
the build breaks on x86, in particular. Switch to use of ioread32_rep
and iowrite32_rep to fix build on all architectures and remove the
CONFIG_ARM dependency.

Also update printk formatting to handle a long long dma_addr_t to avoid
warnings on !32-bit architectures.

Signed-off-by: Matt Porter <mporter@linaro.org>
---
drivers/usb/gadget/Kconfig | 1 -
drivers/usb/gadget/s3c-hsotg.c | 12 ++++++------
2 files changed, 6 insertions(+), 7 deletions(-)

diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig
index 8154165..782f43a 100644
--- a/drivers/usb/gadget/Kconfig
+++ b/drivers/usb/gadget/Kconfig
@@ -301,7 +301,6 @@ config USB_PXA27X
gadget drivers to also be dynamically linked.

config USB_S3C_HSOTG
- depends on ARM
tristate "Designware/S3C HS/OtG USB Device controller"
help
The Designware USB2.0 high-speed gadget controller
diff --git a/drivers/usb/gadget/s3c-hsotg.c b/drivers/usb/gadget/s3c-hsotg.c
index 1172eae..0449b76 100644
--- a/drivers/usb/gadget/s3c-hsotg.c
+++ b/drivers/usb/gadget/s3c-hsotg.c
@@ -617,7 +617,7 @@ static int s3c_hsotg_write_fifo(struct s3c_hsotg *hsotg,
to_write = DIV_ROUND_UP(to_write, 4);
data = hs_req->req.buf + buf_pos;

- writesl(hsotg->regs + EPFIFO(hs_ep->index), data, to_write);
+ iowrite32_rep(hsotg->regs + EPFIFO(hs_ep->index), data, to_write);

return (to_write >= can_write) ? -ENOSPC : 0;
}
@@ -720,8 +720,8 @@ static void s3c_hsotg_start_req(struct s3c_hsotg *hsotg,
ureq->length, ureq->actual);
if (0)
dev_dbg(hsotg->dev,
- "REQ buf %p len %d dma 0x%08x noi=%d zp=%d snok=%d\n",
- ureq->buf, length, ureq->dma,
+ "REQ buf %p len %d dma 0x%08llx noi=%d zp=%d snok=%d\n",
+ ureq->buf, length, (unsigned long long)ureq->dma,
ureq->no_interrupt, ureq->zero, ureq->short_not_ok);

maxreq = get_ep_limit(hs_ep);
@@ -789,8 +789,8 @@ static void s3c_hsotg_start_req(struct s3c_hsotg *hsotg,
dma_reg = dir_in ? DIEPDMA(index) : DOEPDMA(index);
writel(ureq->dma, hsotg->regs + dma_reg);

- dev_dbg(hsotg->dev, "%s: 0x%08x => 0x%08x\n",
- __func__, ureq->dma, dma_reg);
+ dev_dbg(hsotg->dev, "%s: 0x%08llx => 0x%08x\n",
+ __func__, (unsigned long long)ureq->dma, dma_reg);
}

ctrl |= DxEPCTL_EPEna; /* ensure ep enabled */
@@ -1488,7 +1488,7 @@ static void s3c_hsotg_rx_data(struct s3c_hsotg *hsotg, int ep_idx, int size)
* note, we might over-write the buffer end by 3 bytes depending on
* alignment of the data.
*/
- readsl(fifo, hs_req->req.buf + read_ptr, to_read);
+ ioread32_rep(fifo, hs_req->req.buf + read_ptr, to_read);
}

/**
--
1.8.4


\
 
 \ /
  Last update: 2014-02-03 17:21    [W:0.023 / U:0.164 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site