lkml.org 
[lkml]   [2014]   [Dec]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [RFC/PATCH] extcon: otg_gpio: add driver for USB OTG port controlled by GPIO(s)
Hello.

On 12/23/2014 1:43 AM, David Cohen wrote:

> Some platforms have an USB OTG port fully (or partially) controlled by
> GPIOs:

> (1) USB ID is connected directly to GPIO

> Optionally:
> (2) VBUS is enabled by a GPIO (when ID is grounded)

Can't the host driver still control Vbus?

> (3) Platform has 2 USB controllers connected to same port: one for
> device and one for host role. D+/- are switched between phys
> by GPIO.

> As per initial version, this driver has the duty to control whether
> USB-Host cable is plugged in or not:
> - If yes, OTG port is configured for host role
> - If no, by standard, the OTG port is configured for device role

> Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
> ---

> Hi,

> Some Intel Bay Trail boards have an unusual way to handle the USB OTG port:
> - The USB ID pin is connected directly to GPIO on SoC
> - When in host role, VBUS is provided by enabling a GPIO
> - Device and host roles are supported by 2 independent controllers with D+/-
> pins from port switched between different phys according a GPIO level.

> The ACPI table describes this USB port as a (virtual) device with all the
> necessary GPIOs. This driver implements support to this virtual device as an
> extcon class driver. All drivers that depend on the USB OTG port state (USB phy,
> PMIC, charge detection) will listen to extcon events.

It's very close to my setup on R-Car R8A7791 based boards. :-)
I have already submitted Maxim MAX3355 OTG chip GPIO-based driver.

> Comments are welcome.

> Br, David
> ---
>
> drivers/extcon/Kconfig | 8 ++
> drivers/extcon/Makefile | 1 +
> drivers/extcon/extcon-otg_gpio.c | 200 +++++++++++++++++++++++++++++++++++++++
> 3 files changed, 209 insertions(+)
> create mode 100644 drivers/extcon/extcon-otg_gpio.c
>
> diff --git a/drivers/extcon/Kconfig b/drivers/extcon/Kconfig
> index 6a1f7de6fa54..e8010cda4642 100644
> --- a/drivers/extcon/Kconfig
> +++ b/drivers/extcon/Kconfig
> @@ -93,4 +93,12 @@ config EXTCON_SM5502
> Silicon Mitus SM5502. The SM5502 is a USB port accessory
> detector and switch.
>
> +config EXTCON_OTG_GPIO
> + tristate "VIRTUAL USB OTG PORT support"
> + depends on GPIOLIB
> + help
> + Say Y here to enable support for virtual USB OTG port device
> + controlled by GPIOs. This driver can be used when at least USB ID pin
> + is connected directly to GPIO.
> +

The entries in this file seem alphabetically sorted.

> endif # MULTISTATE_SWITCH
> diff --git a/drivers/extcon/Makefile b/drivers/extcon/Makefile
> index 0370b42e5a27..9e81088c6584 100644
> --- a/drivers/extcon/Makefile
> +++ b/drivers/extcon/Makefile
> @@ -12,3 +12,4 @@ obj-$(CONFIG_EXTCON_MAX8997) += extcon-max8997.o
> obj-$(CONFIG_EXTCON_PALMAS) += extcon-palmas.o
> obj-$(CONFIG_EXTCON_RT8973A) += extcon-rt8973a.o
> obj-$(CONFIG_EXTCON_SM5502) += extcon-sm5502.o
> +obj-$(CONFIG_EXTCON_OTG_GPIO) += extcon-otg_gpio.o

The lines here are sorted too.

> diff --git a/drivers/extcon/extcon-otg_gpio.c b/drivers/extcon/extcon-otg_gpio.c
> new file mode 100644
> index 000000000000..c5ee765a5f4f
> --- /dev/null
> +++ b/drivers/extcon/extcon-otg_gpio.c
> @@ -0,0 +1,200 @@
[...]
> +static irqreturn_t vuport_isr(int irq, void *priv)
> +{
> + return IRQ_WAKE_THREAD;
> +}

It's the same as the default IRQ handler...

> + ret = devm_request_threaded_irq(dev, gpiod_to_irq(vup->gpio_usb_id),
> + vuport_isr, vuport_thread_isr,

... so you probably can just pass NULL instead of vuport_isr, no?

[...]

> +static int __init vuport_init(void)
> +{
> + return platform_driver_register(&vuport_driver);
> +}
> +subsys_initcall(vuport_init);

Hm, why?

WBR, Sergei



\
 
 \ /
  Last update: 2014-12-23 14:41    [W:0.169 / U:0.332 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site