lkml.org 
[lkml]   [2014]   [Dec]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH RFC v4 15/21] Documentation: dt-bindings: Add bindings for HIMAX HX8369A DRM panel driver
Date
This patch adds device tree bindings for HIMAX HX8369A DRM panel driver.

Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
---
v3->v4:
* Newly introduced in v4. This is separated from the relevant driver patch
in v3 to address Stefan Wahren's comment.

.../devicetree/bindings/panel/himax,hx8369a.txt | 41 ++++++++++++++++++++++
1 file changed, 41 insertions(+)
create mode 100644 Documentation/devicetree/bindings/panel/himax,hx8369a.txt

diff --git a/Documentation/devicetree/bindings/panel/himax,hx8369a.txt b/Documentation/devicetree/bindings/panel/himax,hx8369a.txt
new file mode 100644
index 0000000..36a2f11
--- /dev/null
+++ b/Documentation/devicetree/bindings/panel/himax,hx8369a.txt
@@ -0,0 +1,41 @@
+Himax HX8369A WVGA 16.7M color TFT single chip driver with internal GRAM
+
+Himax HX8369A is a WVGA resolution driving controller.
+It is designed to provide a single chip solution that combines a source
+driver and power supply circuits to drive a TFT dot matrix LCD with
+480RGBx864 dots at the maximum.
+
+The HX8369A supports several interface modes, including MPU MIPI DBI Type
+A/B mode, MIPI DPI/DBI Type C mode, MIPI DSI video mode, MIPI DSI command
+mode and MDDI mode. The interface mode is selected by the external hardware
+pins BS[3:0].
+
+Currently, only the MIPI DSI video mode is supported.
+
+Required properties:
+ - compatible: should be a panel's compatible string
+ - reg: the virtual channel number of a DSI peripheral as described in [1]
+ - reset-gpios: a GPIO spec for the reset pin
+
+Optional properties:
+ - vdd1-supply: I/O and interface power supply
+ - vdd2-supply: analog power supply
+ - vdd3-supply: logic power supply
+ - dsi-vcc-supply: DSI and MDDI power supply
+ - vpp-supply: OTP programming voltage
+ - bs0-gpios: a GPIO spec for the pin BS0
+ - bs1-gpios: a GPIO spec for the pin BS1
+ - bs2-gpios: a GPIO spec for the pin BS2
+ - bs3-gpios: a GPIO spec for the pin BS3
+
+[1] Documentation/devicetree/bindings/mipi/dsi/mipi-dsi-bus.txt
+
+Example:
+ panel {
+ compatible = "truly,tft480800-16-e-dsi";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mipi_panel>;
+ reset-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
+ bs2-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>;
+ };
--
2.1.0


\
 
 \ /
  Last update: 2014-12-23 11:41    [W:0.098 / U:0.196 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site