lkml.org 
[lkml]   [2014]   [Nov]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 6/6] ARM: dts: sun9i: Enable USB support on A80 Optimus board
Date
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
This patch does not use sunxi-common-regulators.dtsi, but adds the
regulators directly. To use the common regulators file, we would
need to use phandles and switch to preprocessor includes to support
that.

---
arch/arm/boot/dts/sun9i-a80-optimus.dts | 72 +++++++++++++++++++++++++++++++++
1 file changed, 72 insertions(+)

diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts
index 506948f..31010c1 100644
--- a/arch/arm/boot/dts/sun9i-a80-optimus.dts
+++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
@@ -59,6 +59,40 @@
};

soc {
+ ehci0: usb@00a00000 {
+ status = "okay";
+ };
+
+ ohci0: usb@00a00400 {
+ status = "okay";
+ };
+
+ usbphy0: phy@00a00800 {
+ vbus-supply = <&reg_usb0_vbus>;
+ status = "okay";
+ };
+
+ ehci1: usb@00a01000 {
+ status = "okay";
+ };
+
+ usbphy1: phy@00a01800 {
+ status = "okay";
+ };
+
+ ehci2: usb@00a02000 {
+ status = "okay";
+ };
+
+ ohci2: usb@00a02400 {
+ status = "okay";
+ };
+
+ usbphy2: phy@00a02800 {
+ vbus-supply = <&reg_usb2_vbus>;
+ status = "okay";
+ };
+
pio: pinctrl@06000800 {
i2c3_pins_a: i2c3@0 {
/* Enable internal pull-up */
@@ -76,6 +110,20 @@
/* Enable internal pull-up */
allwinner,pull = <1>;
};
+
+ usb0_vbus_pin_optimus: usb0_vbus_pin@1 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <0>;
+ allwinner,pull = <0>;
+ };
+
+ usb2_vbus_pin_optimus: usb2_vbus_pin@1 {
+ allwinner,pins = "PH5";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <0>;
+ allwinner,pull = <0>;
+ };
};

uart0: serial@07000000 {
@@ -116,4 +164,28 @@
gpios = <&pio 7 0 0>;
};
};
+
+ reg_usb0_vbus: usb0-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_vbus_pin_optimus>;
+ regulator-name = "usb0-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&pio 7 4 0>; /* PH4 */
+ status = "okay";
+ };
+
+ reg_usb2_vbus: usb2-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb2_vbus_pin_optimus>;
+ regulator-name = "usb2-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&pio 7 5 0>; /* PH5 */
+ status = "okay";
+ };
};
--
2.1.1


\
 
 \ /
  Last update: 2014-11-04 05:41    [W:0.104 / U:0.104 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site