lkml.org 
[lkml]   [2014]   [Jan]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v5 3/8] ARM: brcmstb: add debug UART for earlyprintk support
Date
Add the UART definitions needed to support earlyprintk on brcmstb machines.

Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
---
arch/arm/Kconfig.debug | 16 +++++++++++++++-
1 files changed, 15 insertions(+), 1 deletions(-)

diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index 5765abf..666afd7 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -94,6 +94,17 @@ choice
depends on ARCH_BCM2835
select DEBUG_UART_PL01X

+ config DEBUG_BRCMSTB_UART
+ bool "Use BRCMSTB UART for low-level debug"
+ depends on ARCH_BRCMSTB
+ select DEBUG_UART_8250
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to the first serial port on these devices.
+
+ If you have a Broadcom STB chip and would like early print
+ messages to appear over the UART, select this option.
+
config DEBUG_CLPS711X_UART1
bool "Kernel low-level debugging messages via UART1"
depends on ARCH_CLPS711X
@@ -1008,6 +1019,7 @@ config DEBUG_UART_PHYS
default 0xd4018000 if DEBUG_MMP_UART3
default 0xe0000000 if ARCH_SPEAR13XX
default 0xf0000be0 if ARCH_EBSA110
+ default 0xf0406b00 if DEBUG_BRCMSTB_UART
default 0xf1012000 if DEBUG_MVEBU_UART_ALTERNATE
default 0xf1012000 if ARCH_DOVE || ARCH_KIRKWOOD || ARCH_MV78XX0 || \
ARCH_ORION5X
@@ -1040,6 +1052,7 @@ config DEBUG_UART_VIRT
default 0xf8090000 if DEBUG_VEXPRESS_UART0_RS1
default 0xfb009000 if DEBUG_REALVIEW_STD_PORT
default 0xfb10c000 if DEBUG_REALVIEW_PB1176_PORT
+ default 0xfc406b00 if DEBUG_BRCMSTB_UART
default 0xfd000000 if ARCH_SPEAR3XX || ARCH_SPEAR6XX
default 0xfd000000 if ARCH_SPEAR13XX
default 0xfd012000 if ARCH_MV78XX0
@@ -1091,7 +1104,8 @@ config DEBUG_UART_8250_WORD
default y if DEBUG_PICOXCELL_UART || DEBUG_SOCFPGA_UART || \
ARCH_KEYSTONE || \
DEBUG_DAVINCI_DMx_UART0 || DEBUG_DAVINCI_DA8XX_UART1 || \
- DEBUG_DAVINCI_DA8XX_UART2 || DEBUG_DAVINCI_TNETV107X_UART1
+ DEBUG_DAVINCI_DA8XX_UART2 || DEBUG_DAVINCI_TNETV107X_UART1 || \
+ DEBUG_BRCMSTB_UART

config DEBUG_UART_8250_FLOW_CONTROL
bool "Enable flow control for 8250 UART"
--
1.7.1


\
 
 \ /
  Last update: 2014-01-22 05:01    [W:0.702 / U:0.072 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site