lkml.org 
[lkml]   [2013]   [Mar]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v7 02/14] spi/spi-atmel: add support transfer on CS1,2,3, not only on CS0
Date
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Cc: spi-devel-general@lists.sourceforge.net
Cc: linux-kernel@vger.kernel.org
---
drivers/spi/spi-atmel.c | 25 ++++++++++++-------------
1 file changed, 12 insertions(+), 13 deletions(-)

diff --git a/drivers/spi/spi-atmel.c b/drivers/spi/spi-atmel.c
index 0928dee..64e2795 100644
--- a/drivers/spi/spi-atmel.c
+++ b/drivers/spi/spi-atmel.c
@@ -255,11 +255,6 @@ static bool atmel_spi_is_v2(struct atmel_spi *as)
* Master on Chip Select 0.") No workaround exists for that ... so for
* nCS0 on that chip, we (a) don't use the GPIO, (b) can't support CS_HIGH,
* and (c) will trigger that first erratum in some cases.
- *
- * TODO: Test if the atmel_spi_is_v2() branch below works on
- * AT91RM9200 if we use some other register than CSR0. However, don't
- * do this unconditionally since AP7000 has an errata where the BITS
- * field in CSR0 overrides all other CSRs.
*/

static void cs_activate(struct atmel_spi *as, struct spi_device *spi)
@@ -269,18 +264,22 @@ static void cs_activate(struct atmel_spi *as, struct spi_device *spi)
u32 mr;

if (atmel_spi_is_v2(as)) {
- /*
- * Always use CSR0. This ensures that the clock
- * switches to the correct idle polarity before we
- * toggle the CS.
+ spi_writel(as, CSR0 + 4 * spi->chip_select, asd->csr);
+ /* For the low SPI version, there is a issue that PDC transfer
+ * on CS1,2,3 needs SPI_CSR0.BITS config as SPI_CSR1,2,3.BITS
*/
spi_writel(as, CSR0, asd->csr);
if (as->caps.has_wdrbt) {
- spi_writel(as, MR, SPI_BF(PCS, 0x0e) | SPI_BIT(WDRBT)
- | SPI_BIT(MODFDIS) | SPI_BIT(MSTR));
+ spi_writel(as, MR,
+ SPI_BF(PCS, ~(0x01 << spi->chip_select))
+ | SPI_BIT(WDRBT)
+ | SPI_BIT(MODFDIS)
+ | SPI_BIT(MSTR));
} else {
- spi_writel(as, MR, SPI_BF(PCS, 0x0e) | SPI_BIT(MODFDIS)
- | SPI_BIT(MSTR));
+ spi_writel(as, MR,
+ SPI_BF(PCS, ~(0x01 << spi->chip_select))
+ | SPI_BIT(MODFDIS)
+ | SPI_BIT(MSTR));
}
mr = spi_readl(as, MR);
gpio_set_value(asd->npcs_pin, active);
--
1.7.9.5


\
 
 \ /
  Last update: 2013-03-19 09:01    [W:0.754 / U:0.172 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site