lkml.org 
[lkml]   [2013]   [Feb]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] ARM: OMAP: gpmc: Add device tree documentation for elm handle
* Philip Avinash <avinashphilip@ti.com> [130117 21:00]:
> In case ELM module available, omap2 NAND driver can opt for hardware
> correction method for bit flip errors in NAND flash with BCH. Hence the
> detection of ELM module is done through devicetree population of elm_id.
> This patch update device tree documentation for gpmc-nand for elm-id
> data population.
>
> Signed-off-by: Philip Avinash <avinashphilip@ti.com>
> ---
> This patch based [1] and depends on [2]. As Artem suggested, this patch can
> go in omap_tree due to the dependency on [3].
> Discussion can found at [4]
>
> Tony,
> Can you accept this patch.

Thanks applying into omap-for-v3.9/gpmc.

Regards,

Tony

> 1. http://git.kernel.org/?p=linux/kernel/git/tmlind/linux-omap.git;a=shortlog;h=refs/heads/omap-for-v3.9/gpmc
> 2. mtd: nand: omap2: Support for hardware BCH error correction
> http://git.infradead.org/users/dedekind/l2-mtd-2.6.git/commit/576daed18c3f27bb5d0e57e1df11e8f7b493dce8
> 3. ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND
> http://git.kernel.org/?p=linux/kernel/git/tmlind/linux-omap.git;a=commit;h=bc6b1e7b86f5d8e4a6fc1c0189e64bba4077efe0
> 4. https://lkml.org/lkml/2013/1/17/167
>
> .../devicetree/bindings/mtd/gpmc-nand.txt | 4 ++++
> 1 file changed, 4 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
> index 9f464f9..e7f8d7e 100644
> --- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
> +++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
> @@ -29,6 +29,9 @@ Optional properties:
> "bch4" 4-bit BCH ecc code
> "bch8" 8-bit BCH ecc code
>
> + - elm_id: Specifies elm device node. This is required to support BCH
> + error correction using ELM module.
> +
> For inline partiton table parsing (optional):
>
> - #address-cells: should be set to 1
> @@ -46,6 +49,7 @@ Example for an AM33xx board:
> #address-cells = <2>;
> #size-cells = <1>;
> ranges = <0 0 0x08000000 0x2000>; /* CS0: NAND */
> + elm_id = <&elm>;
>
> nand@0,0 {
> reg = <0 0 0>; /* CS0, offset 0 */
> --
> 1.7.9.5
>


\
 
 \ /
  Last update: 2013-02-01 23:42    [W:0.066 / U:0.112 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site