[lkml]   [2013]   [Dec]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
Messages in this thread
Subject[PATCH V5 0/4] DRIVERS: IRQCHIP: Add support for crossbar IP
Some socs have a large number of interrupts requests to service
the needs of its many peripherals and subsystems. All of the interrupt
requests lines from the subsystems are not needed at the same
time, so they have to be muxed to the controllers appropriately.
In such places a interrupt controllers are preceded by an
IRQ CROSSBAR that provides flexibility in muxing the device interrupt
requests to the controller inputs.

This series models the peripheral interrupts that can be routed through
the crossbar to the GIC as 'routable-irqs'. The routable irqs are added
in a separate linear domain inside the GIC. The registered routable domain's
callback are invoked as a part of the GIC's callback, which in turn should
allocate a free irq line and configure the IP accordingly. So every peripheral
in the dts files mentions the fixed crossbar number as its interrupt. A free
gic line for that gets allocated and configured when the peripheral interrupts
are mapped.

The minimal crossbar driver to track and allocate free GIC lines and configure the
crossbar is added here, along with the DT bindings.

Addressed a comment from Mark Rutland <>,
updated tags and rebased on 3.13-rc2

Addressed a couple of comments and split the DTS file updates in to
a separate series.

Addressed few more comments from Thomas Gleixner <>

Rebased patches 3,4,5,7 which updates the DTS file on top of below branch

Rebased patches 1,2,6 on top of 3.12 mainline
Updated Commit tags

Addressed Thomas Gleixner <> comments and
Kumar Gala <>

Split updating the DRA7.dtsi file for adding the routable-irqs

Previous discussions that led to this is at

The V1,V2,V3,V4 post of these patches is at

Sricharan R (4):
DRIVERS: IRQCHIP: IRQ-GIC: Add support for routable irqs
DRIVERS: IRQCHIP: CROSSBAR: Add support for Crossbar IP
ARM: OMAP4+: Correct Wakeup-gen code to use physical irq number
ARM: DRA: Enable Crossbar IP support for DRA7XX

Documentation/devicetree/bindings/arm/gic.txt | 6 +
.../devicetree/bindings/arm/omap/crossbar.txt | 27 +++
arch/arm/mach-omap2/Kconfig | 1 +
arch/arm/mach-omap2/omap-wakeupgen.c | 4 +-
arch/arm/mach-omap2/omap4-common.c | 2 +
drivers/irqchip/Kconfig | 8 +
drivers/irqchip/Makefile | 1 +
drivers/irqchip/irq-crossbar.c | 208 ++++++++++++++++++++
drivers/irqchip/irq-gic.c | 81 +++++++-
include/linux/irqchip/arm-gic.h | 7 +-
include/linux/irqchip/irq-crossbar.h | 11 ++
11 files changed, 343 insertions(+), 13 deletions(-)
create mode 100644 Documentation/devicetree/bindings/arm/omap/crossbar.txt
create mode 100644 drivers/irqchip/irq-crossbar.c
create mode 100644 include/linux/irqchip/irq-crossbar.h


 \ /
  Last update: 2013-12-03 11:41    [W:0.097 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site