lkml.org 
[lkml]   [2013]   [Nov]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 5/9] ARM: at91/dt: add mmc0 slot0 support to at91rm9200ek board
On 20/11/2013 15:59, Jean-Christophe PLAGNIOL-VILLARD wrote:
> On 13:06 Wed 28 Aug , Boris BREZILLON wrote:
>> Add slot0 of mmc0 pinctrl pins definitions:
>> - detect pin
>> - write protect pin
>> - enable slot0 pin: this pin is connected to an external switch which
>> enable mmc0 slot0 or spi dataflash connected to cs3
>>
>> The mmc0 device is not enabled, as it depends on the choosen functionnality
>> (spi cs3 or mmc0 slot0).
>>
>> Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
>> ---
>> arch/arm/boot/dts/at91rm9200ek.dts | 35 +++++++++++++++++++++++++++++++++++
>> 1 file changed, 35 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/at91rm9200ek.dts b/arch/arm/boot/dts/at91rm9200ek.dts
>> index f2d6d79..2bad423 100644
>> --- a/arch/arm/boot/dts/at91rm9200ek.dts
>> +++ b/arch/arm/boot/dts/at91rm9200ek.dts
>> @@ -39,6 +39,23 @@
>> atmel,pins = <AT91_PIOD 5 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>;
>> };
>> };
>> +
>> + mmc0 {
>> + pinctrl_mmc0_slot0_detect: mmc0_slot0_detect-0 {
>> + atmel,pins =
>> + <AT91_PIOB 27 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
>> + };
>> +
>> + pinctrl_mmc0_slot0_write_protect: mmc0_slot0_write_protect-0 {
>> + atmel,pins =
>> + <AT91_PIOA 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
>> + };
>> +
>> + pinctrl_mmc0_slot0_switch: mmc0_slot0_switch-0 {
>> + atmel,pins =
>> + <AT91_PIOB 22 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(1))>;
>> + };
> nack this is a regulator the pinctrl API is not done for gpio default value

I know this can be represented as a regulator, but looking at the
datasheet, this looks more
like a switch than a regulator.

Anyway, why didn't you told me that when I proposed the OUTPUT support
for at91 pinctrl driver ?
And BTW pinctrl OUTPUT config is already supported by some pinctrl drivers
(
http://lxr.free-electrons.com/source/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt#L159).

>> + };
>> };
>>
>> dbgu: serial@fffff200 {
>> @@ -84,6 +101,24 @@
>> reg = <0>;
>> };
>> };
>> +
>> + mmc0: mmc@fffb4000 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + pinctrl-0 = <&pinctrl_mmc0_clk
>> + &pinctrl_mmc0_slot0_cmd_dat0
>> + &pinctrl_mmc0_slot0_dat1_3
>> + &pinctrl_mmc0_slot0_detect
>> + &pinctrl_mmc0_slot0_write_protect
>> + &pinctrl_mmc0_slot0_switch>;
>> +
>> + slot0: slot@0 {
>> + reg = <0>;
>> + bus-width = <4>;
>> + cd-gpios = <&pioB 27 GPIO_ACTIVE_HIGH>;
>> + wp-gpios = <&pioA 17 GPIO_ACTIVE_HIGH>;
>> + };
>> + };
>> };
>>
>> usb0: ohci@00300000 {
>> --
>> 1.7.9.5
>>



\
 
 \ /
  Last update: 2013-11-20 17:41    [W:0.358 / U:1.120 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site