lkml.org 
[lkml]   [2013]   [Jan]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCHv3 6/8] serial: 8250_dw: Add ACPI 5.0 support
Date
This adds support for ACPI 5.0 enumerated Designware UARTs.
ACPI does not deliver information about uart clk, so
delivering it with the driver_data.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
---
drivers/tty/serial/8250/8250_dw.c | 41 +++++++++++++++++++++++++++++++++++++
drivers/tty/serial/8250/Kconfig | 2 +-
2 files changed, 42 insertions(+), 1 deletion(-)

diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
index e104092..f6eeff0 100644
--- a/drivers/tty/serial/8250/8250_dw.c
+++ b/drivers/tty/serial/8250/8250_dw.c
@@ -2,6 +2,7 @@
* Synopsys DesignWare 8250 driver.
*
* Copyright 2011 Picochip, Jamie Iles.
+ * Copyright 2013 Intel Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
@@ -24,12 +25,16 @@
#include <linux/of_platform.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
+#include <linux/acpi.h>

/* Offsets for the DesignWare specific registers */
#define DW_UART_USR 0x1f /* UART Status Register */
#define DW_UART_CPR 0xf4 /* Component Parameter Register */
#define DW_UART_UCV 0xf8 /* UART Component Version */

+/* Intel Low Power Subsystem specific */
+#define LPSS_PRV_CLOCK_PARAMS 0x800
+
/* Component Parameter Register bits */
#define DW_UART_CPR_ABP_DATA_WIDTH (3 << 0)
#define DW_UART_CPR_AFCE_MODE (1 << 4)
@@ -138,6 +143,30 @@ static int dw8250_probe_of(struct uart_port *p)
return 0;
}

+static int dw8250_probe_acpi(struct uart_port *p)
+{
+ const struct acpi_device_id *id;
+ u32 reg;
+
+ id = acpi_match_device(p->dev->driver->acpi_match_table, p->dev);
+ if (!id)
+ return -ENODEV;
+
+ p->iotype = UPIO_MEM32;
+ p->serial_in = dw8250_serial_in32;
+ p->serial_out = dw8250_serial_out32;
+ p->regshift = 2;
+ p->uartclk = (unsigned int)id->driver_data;
+
+ /* Fix Haswell issue where the clocks do not get enabled */
+ if (!strcmp(id->id, "INT33C4") || !strcmp(id->id, "INT33C5")) {
+ reg = readl(p->membase + LPSS_PRV_CLOCK_PARAMS);
+ writel(reg | 1, p->membase + LPSS_PRV_CLOCK_PARAMS);
+ }
+
+ return 0;
+}
+
static void dw8250_setup_port(struct uart_8250_port *up)
{
struct uart_port *p = &up->port;
@@ -199,6 +228,10 @@ static int dw8250_probe(struct platform_device *pdev)
err = dw8250_probe_of(&uart.port);
if (err)
return err;
+ } else if (ACPI_HANDLE(&pdev->dev)) {
+ err = dw8250_probe_acpi(&uart.port);
+ if (err)
+ return err;
} else {
return -ENODEV;
}
@@ -258,11 +291,19 @@ static const struct of_device_id dw8250_of_match[] = {
};
MODULE_DEVICE_TABLE(of, dw8250_of_match);

+static const struct acpi_device_id dw8250_acpi_match[] = {
+ { "INT33C4", 100000000 },
+ { "INT33C5", 100000000 },
+ { },
+};
+MODULE_DEVICE_TABLE(acpi, dw8250_acpi_match);
+
static struct platform_driver dw8250_platform_driver = {
.driver = {
.name = "dw-apb-uart",
.owner = THIS_MODULE,
.of_match_table = dw8250_of_match,
+ .acpi_match_table = ACPI_PTR(dw8250_acpi_match),
},
.probe = dw8250_probe,
.remove = dw8250_remove,
diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig
index c31133a..11adff1 100644
--- a/drivers/tty/serial/8250/Kconfig
+++ b/drivers/tty/serial/8250/Kconfig
@@ -265,7 +265,7 @@ config SERIAL_8250_FSL

config SERIAL_8250_DW
tristate "Support for Synopsys DesignWare 8250 quirks"
- depends on SERIAL_8250 && OF
+ depends on SERIAL_8250
help
Selecting this option will enable handling of the extra features
present in the Synopsys DesignWare APB UART.
--
1.7.10.4


\
 
 \ /
  Last update: 2013-01-10 11:43    [W:0.090 / U:0.768 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site