lkml.org 
[lkml]   [2012]   [Aug]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Subject[PATCH 0/1] xhci: Unconditionally switch ports to xHCI on powerup
Date
From: Manoj Iyer <manoj.iyer@canonical.com>

USB 3.0 devices show up as high-speed devices on powerup, after an
s3 cycle they are correctly recognized as SuperSpeed. At powerup
unconditionally switch the port to xHCI like we do when we resume
from suspend.

BugLink: http://bugs.launchpad.net/bugs/1000424

Test results:
This patch was tested by me on a Lenovo system:

00:14.0 USB controller [0c03]: Intel Corporation Panther Point USB xHCI Host Con
troller [8086:1e31] (rev 04) (prog-if 30 [XHCI])
Subsystem: Lenovo Device [17aa:5002]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort
- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 41
Region 0: Memory at 90600000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3h
ot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+
Address: 00000000fee0300c Data: 4169
Kernel driver in use: xhci_hcd

== BEFORE PATCH ==
[ 25.982350] eth1: no IPv6 routers present
[ 27.577663] usb 2-1.1: new high-speed USB device number 3 using ehci_hcd
[ 27.674465] scsi6 : usb-storage 2-1.1:1.0
[ 28.673788] scsi 6:0:0:0: Direct-Access JetFlash Transcend 16GB 1.00 PQ: 0 ANSI: 5
[ 28.674667] sd 6:0:0:0: Attached scsi generic sg3 type 0
[ 28.677284] sd 6:0:0:0: [sdc] 30871552 512-byte logical blocks: (15.8 GB/14.7 GiB)
[ 28.677832] sd 6:0:0:0: [sdc] Write Protect is off
[ 28.677839] sd 6:0:0:0: [sdc] Mode Sense: 23 00 00 00
[ 28.678454] sd 6:0:0:0: [sdc] Write cache: disabled, read cache: disabled, doesn't support DPO or FUA
[ 28.682117] sdc: sdc1
[ 28.684179] sd 6:0:0:0: [sdc] Attached SCSI removable disk

== AFTER PATCH USB 3.0 PORT ==
[ 56.653501] usb 4-1: new SuperSpeed USB device number 2 using xhci_hcd
[ 56.672677] scsi6 : usb-storage 4-1:1.0
[ 57.669912] scsi 6:0:0:0: Direct-Access JetFlash Transcend 16GB 1.00 PQ: 0 ANSI: 5
[ 57.671100] sd 6:0:0:0: [sdc] 30871552 512-byte logical blocks: (15.8 GB/14.7 GiB)
[ 57.671185] sd 6:0:0:0: Attached scsi generic sg3 type 0
[ 57.671389] sd 6:0:0:0: [sdc] Write Protect is off
[ 57.671392] sd 6:0:0:0: [sdc] Mode Sense: 23 00 00 00
[ 57.671499] sd 6:0:0:0: [sdc] Write cache: disabled, read cache: disabled, doesn't support DPO or FUA
[ 57.674480] sdc: sdc1
[ 57.675180] sd 6:0:0:0: [sdc] Attached SCSI removable disk


== AFTER PATCH USB 2.0 PORT ==
[ 112.468810] usb 4-1: USB disconnect, device number 2
[ 117.688925] usb 1-1.2: new high-speed USB device number 5 using ehci_hcd
[ 117.786131] scsi7 : usb-storage 1-1.2:1.0
[ 118.785809] scsi 7:0:0:0: Direct-Access JetFlash Transcend 16GB 1.00 PQ: 0 ANSI: 5
[ 118.788004] sd 7:0:0:0: Attached scsi generic sg3 type 0
[ 118.789848] sd 7:0:0:0: [sdc] 30871552 512-byte logical blocks: (15.8 GB/14.7 GiB)
[ 118.790287] sd 7:0:0:0: [sdc] Write Protect is off
[ 118.790294] sd 7:0:0:0: [sdc] Mode Sense: 23 00 00 00
[ 118.791072] sd 7:0:0:0: [sdc] Write cache: disabled, read cache: disabled, doesn't support DPO or FUA
[ 118.796448] sdc: sdc1
[ 118.798525] sd 7:0:0:0: [sdc] Attached SCSI removable disk

Manoj Iyer (1):
xhci: Unconditionally switch ports to xHCI on powerup

drivers/usb/host/xhci-pci.c | 8 ++++++++
1 file changed, 8 insertions(+)

--
1.7.9.5



\
 
 \ /
  Last update: 2012-08-21 06:41    [W:0.073 / U:0.448 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site