lkml.org 
[lkml]   [2011]   [Nov]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH RESEND v2 2/2] regulator: TPS65910: VDD1/2 voltage selector count
Date
Count of selector voltage is required for regulator_set_voltage
to work via set_voltage_sel. VDD1/2 currently have it as zero,
so regulator_set_voltage won't work for VDD1/2.
Update count (n_voltages) for VDD1/2.

Output Voltage = (step value * 12.5 mV + 562.5 mV) * gain

With above expr, number of voltages that can be selected is
step value count * gain count

constant for gain count will be called VDD1_2_NUM_VOLT_COARSE

existing constant for step value count is VDD1_2_NUM_VOLTS,
use VDD1_2_NUM_VOLT_FINE instead to make clear that step value
is not the only component in deciding selectable voltage count

Signed-off-by: Afzal Mohammed <afzal@ti.com>
---
v2: Use macros unambigously to specify count of selectable voltage

drivers/regulator/tps65910-regulator.c | 14 ++++++++------
include/linux/mfd/tps65910.h | 3 ++-
2 files changed, 10 insertions(+), 7 deletions(-)

diff --git a/drivers/regulator/tps65910-regulator.c b/drivers/regulator/tps65910-regulator.c
index a620e25..bb2a08d 100644
--- a/drivers/regulator/tps65910-regulator.c
+++ b/drivers/regulator/tps65910-regulator.c
@@ -640,10 +640,10 @@ static int tps65910_set_voltage_dcdc(struct regulator_dev *dev,

switch (id) {
case TPS65910_REG_VDD1:
- dcdc_mult = (selector / VDD1_2_NUM_VOLTS) + 1;
+ dcdc_mult = (selector / VDD1_2_NUM_VOLT_FINE) + 1;
if (dcdc_mult == 1)
dcdc_mult--;
- vsel = (selector % VDD1_2_NUM_VOLTS) + 3;
+ vsel = (selector % VDD1_2_NUM_VOLT_FINE) + 3;

tps65910_modify_bits(pmic, TPS65910_VDD1,
(dcdc_mult << VDD1_VGAIN_SEL_SHIFT),
@@ -651,10 +651,10 @@ static int tps65910_set_voltage_dcdc(struct regulator_dev *dev,
tps65910_reg_write(pmic, TPS65910_VDD1_OP, vsel);
break;
case TPS65910_REG_VDD2:
- dcdc_mult = (selector / VDD1_2_NUM_VOLTS) + 1;
+ dcdc_mult = (selector / VDD1_2_NUM_VOLT_FINE) + 1;
if (dcdc_mult == 1)
dcdc_mult--;
- vsel = (selector % VDD1_2_NUM_VOLTS) + 3;
+ vsel = (selector % VDD1_2_NUM_VOLT_FINE) + 3;

tps65910_modify_bits(pmic, TPS65910_VDD2,
(dcdc_mult << VDD2_VGAIN_SEL_SHIFT),
@@ -732,9 +732,9 @@ static int tps65910_list_voltage_dcdc(struct regulator_dev *dev,
switch (id) {
case TPS65910_REG_VDD1:
case TPS65910_REG_VDD2:
- mult = (selector / VDD1_2_NUM_VOLTS) + 1;
+ mult = (selector / VDD1_2_NUM_VOLT_FINE) + 1;
volt = VDD1_2_MIN_VOLT +
- (selector % VDD1_2_NUM_VOLTS) * VDD1_2_OFFSET;
+ (selector % VDD1_2_NUM_VOLT_FINE) * VDD1_2_OFFSET;
break;
case TPS65911_REG_VDDCTRL:
volt = VDDCTRL_MIN_VOLT + (selector * VDDCTRL_OFFSET);
@@ -930,6 +930,8 @@ static __devinit int tps65910_probe(struct platform_device *pdev)

if (i == TPS65910_REG_VDD1 || i == TPS65910_REG_VDD2) {
pmic->desc[i].ops = &tps65910_ops_dcdc;
+ pmic->desc[i].n_voltages = VDD1_2_NUM_VOLT_FINE *
+ VDD1_2_NUM_VOLT_COARSE;
} else if (i == TPS65910_REG_VDD3) {
if (tps65910_chip_id(tps65910) == TPS65910)
pmic->desc[i].ops = &tps65910_ops_vdd3;
diff --git a/include/linux/mfd/tps65910.h b/include/linux/mfd/tps65910.h
index 207b8b2..cfc1f76 100644
--- a/include/linux/mfd/tps65910.h
+++ b/include/linux/mfd/tps65910.h
@@ -250,7 +250,8 @@


/*Registers VDD1, VDD2 voltage values definitions */
-#define VDD1_2_NUM_VOLTS 73
+#define VDD1_2_NUM_VOLT_FINE 73
+#define VDD1_2_NUM_VOLT_COARSE 3
#define VDD1_2_MIN_VOLT 6000
#define VDD1_2_OFFSET 125

--
1.7.0.4


\
 
 \ /
  Last update: 2011-11-08 14:27    [W:0.110 / U:0.356 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site