lkml.org 
[lkml]   [2011]   [Nov]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[PATCH][W1]w1_therm: release the bus during conversion on externally powered devices
w1_therm devices can either be bus powered or externally powered.

When device is bus powered during temperature conversion the bus
have to be left high to provide necessary power. Some masters also allow
strong power-up to be enabled in this case.
Naturally, no communication over bus can occur during that time.

However, if device has external power then there is no such restriction,
and host can talk to other devices during temperature conversion.

There is command which allows us to check how device is powered,
this patch uses it to release the bus on externally w1_therm powered devices
during temperature conversion.

Also, this changes uninterruptible sleeps there into interruptible ones to
avoid long uninterruptible sleep if w1 subsystem happens to grab bus for
scan during w1_therm_read().

Signed-off-by: Maciej Szmigiero <mhej@o2.pl>

diff --git a/drivers/w1/slaves/w1_therm.c b/drivers/w1/slaves/w1_therm.c
index a1ef9b5..ff29ae7 100644
--- a/drivers/w1/slaves/w1_therm.c
+++ b/drivers/w1/slaves/w1_therm.c
@@ -175,11 +175,13 @@ static ssize_t w1_therm_read(struct device *device,
{
struct w1_slave *sl = dev_to_w1_slave(device);
struct w1_master *dev = sl->master;
- u8 rom[9], crc, verdict;
+ u8 rom[9], crc, verdict, external_power;
int i, max_trying = 10;
ssize_t c = PAGE_SIZE;

- mutex_lock(&dev->mutex);
+ i = mutex_lock_interruptible(&dev->mutex);
+ if (i != 0)
+ return i;

memset(rom, 0, sizeof(rom));

@@ -190,13 +192,37 @@ static ssize_t w1_therm_read(struct device *device,
if (!w1_reset_select_slave(sl)) {
int count = 0;
unsigned int tm = 750;
+ unsigned long sleep_rem;
+
+ w1_write_8(dev, W1_READ_PSUPPLY);
+ external_power = w1_read_8(dev);
+
+ if (w1_reset_select_slave(sl))
+ continue;

/* 750ms strong pullup (or delay) after the convert */
- if (w1_strong_pullup)
+ if (!external_power && w1_strong_pullup)
w1_next_pullup(dev, tm);
+
w1_write_8(dev, W1_CONVERT_TEMP);
- if (!w1_strong_pullup)
- msleep(tm);
+
+ if (external_power) {
+ mutex_unlock(&dev->mutex);
+
+ sleep_rem = msleep_interruptible(tm);
+ if (sleep_rem != 0)
+ return -EINTR;
+
+ i = mutex_lock_interruptible(&dev->mutex);
+ if (i != 0)
+ return i;
+ } else if (!w1_strong_pullup) {
+ sleep_rem = msleep_interruptible(tm);
+ if (sleep_rem != 0) {
+ mutex_unlock(&dev->mutex);
+ return -EINTR;
+ }
+ }

if (!w1_reset_select_slave(sl)) {




\
 
 \ /
  Last update: 2011-11-16 00:45    [W:2.655 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site