Messages in this thread | | | Date | Fri, 29 Aug 2008 08:44:16 -0600 | From | Robert Hancock <> | Subject | Re: SATA Cold Boot problems on >2.6.25 with NV |
| |
(ccing linux-ide)
Tejun, another one of these reset issues?
Konstantin Kletschke wrote: > Hello! > > > I found to references regarding this problem in this list. Many Maxwell > reported this and Tejo asked if his supposed fix helps out. > > Another reference by Jeff suggests bisecting a git commit. Since I am > very unexperienced in the git stuff I hope it is okay to start another > initial mail about this to ask > > 1.) What I should try out on the code to trace this further down > > 2.) I would extend this problem on >2.6.25 version of kernel. > > I have an "nForce3 250 chipset" on an Asrock K8Upgrade-NF3 Motherboard > > 00:00.0 Host bridge: nVidia Corporation nForce3 250Gb Host Bridge (rev a1) > 00:01.0 ISA bridge: nVidia Corporation nForce3 250Gb LPC Bridge (rev a2) > 00:01.1 SMBus: nVidia Corporation nForce 250Gb PCI System Management (rev a1) > 00:02.0 USB Controller: nVidia Corporation CK8S USB Controller (rev a1) > 00:02.1 USB Controller: nVidia Corporation CK8S USB Controller (rev a1) > 00:02.2 USB Controller: nVidia Corporation nForce3 EHCI USB 2.0 Controller (rev a2) > 00:05.0 Bridge: nVidia Corporation CK8S Ethernet Controller (rev a2) > 00:06.0 Multimedia audio controller: nVidia Corporation nForce3 250Gb AC'97 Audio Controller (rev a1) > 00:08.0 IDE interface: nVidia Corporation CK8S Parallel ATA Controller (v2.5) (rev a2) > 00:0a.0 IDE interface: nVidia Corporation CK8S Serial ATA Controller (v2.5) (rev a2) > 00:0b.0 PCI bridge: nVidia Corporation nForce3 250Gb AGP Host to PCI Bridge (rev a2) > 00:0e.0 PCI bridge: nVidia Corporation nForce3 250Gb PCI-to-PCI Bridge (rev a2) > 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration > 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map > 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller > 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control > 01:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX 5200] (rev a1) > 02:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) > > While 2.6.25 works very fine I experienced this with 2.6.26_rc7 at first > (I skipped versions between). Cold Boot yields into the described error, > I sadly only have real screenshots of this: > > http://ludenkalle.de/sata > > After a reset the Kernel was not able to do anything useful with the > SATA interface anymore (this description is a bit vague, IIRC it stuck > immediately around "SATA Link down..."). Only powercycling helped out, > then it booted with SATA. > > Now I have 2.6.27-rc3, same error but config netconsole enabled. > Normal Boot: > > ata1: SATA link down (SStatus 0 SControl 300) > ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) > ata2.00: ATA-7: SAMSUNG HD753LJ, 1AA01106, max UDMA7 > ata2.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 0/32) > ata2.00: configured for UDMA/133 > isa bounce pool size: 16 pages > scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD753LJ 1AA0 PQ: 0 ANSI: 5 > sd 1:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB) > sd 1:0:0:0: [sda] Write Protect is off > sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA > sd 1:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB) > sd 1:0:0:0: [sda] Write Protect is off > sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA > sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 > > sd 1:0:0:0: [sda] Attached SCSI disk > PNP: No PS/2 controller found. Probing ports directly. > serio: i8042 KBD port at 0x60,0x64 irq 1 > serio: i8042 AUX port at 0x60,0x64 irq 12 > TCP cubic registered > NET: Registered protocol family 17 > XFS mounting filesystem sda1 > VFS: Mounted root (xfs filesystem) readonly. > Freeing unused kernel memory: 220k freed > > Cold Boot: > > ata1: SATA link down (SStatus 0 SControl 300) > ata2: link is slow to respond, please be patient (ready=0) > ata2: COMRESET failed (errno=-16) > ata2: link is slow to respond, please be patient (ready=0) > ata2: COMRESET failed (errno=-16) > ata2: link is slow to respond, please be patient (ready=0) > ata2: COMRESET failed (errno=-16) > ata2: limiting SATA link speed to 1.5 Gbps > ata2: COMRESET failed (errno=-16) > ata2: reset failed, giving up > PNP: No PS/2 controller found. Probing ports directly. > serio: i8042 KBD port at 0x60,0x64 irq 1 > serio: i8042 AUX port at 0x60,0x64 irq 12 > TCP cubic registered > NET: Registered protocol family 17 > VFS: Cannot open root device "801" or unknown-block(8,1) > Please append a correct "root=" boot option; here are the available partitions: > Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,1) > > Hmn, thats it. Where should I poke into? > > Kind Regards, Konsti > >
| |