Messages in this thread Patch in this message | | | Date | Mon, 5 Nov 2007 18:05:57 +0100 | From | Adrian Bunk <> | Subject | [2.6 patch] remove Documentation/networking/pt.txt |
| |
There's no no point in keeping documentation for a driver that was removed many years ago.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
---
Documentation/networking/00-INDEX | 2 - Documentation/networking/pt.txt | 58 ------------------------------ 2 files changed, 60 deletions(-)
cfe9580e99bc2406a5a05bae24487ca84619bec7 diff --git a/Documentation/networking/00-INDEX b/Documentation/networking/00-INDEX index 9c64042..5e21f37 100644 --- a/Documentation/networking/00-INDEX +++ b/Documentation/networking/00-INDEX @@ -80,6 +80,4 @@ olympic.txt policy-routing.txt - IP policy-based routing -pt.txt - - the Gracilis Packetwin AX.25 device driver ray_cs.txt - Raylink Wireless LAN card driver info. diff --git a/Documentation/networking/pt.txt b/Documentation/networking/pt.txt deleted file mode 100644 index 72e888c..0000000 --- a/Documentation/networking/pt.txt +++ /dev/null @@ -1,58 +0,0 @@ -This is the README for the Gracilis Packetwin device driver, version 0.5 -ALPHA for Linux 1.3.43. - -These files will allow you to talk to the PackeTwin (now know as PT) and -connect through it just like a pair of TNCs. To do this you will also -require the AX.25 code in the kernel enabled. - -There are four files in this archive; this readme, a patch file, a .c file -and finally a .h file. The two program files need to be put into the -drivers/net directory in the Linux source tree, for me this is the -directory /usr/src/linux/drivers/net. The patch file needs to be patched in -at the top of the Linux source tree (/usr/src/linux in my case). - -You will most probably have to edit the pt.c file to suit your own setup, -this should just involve changing some of the defines at the top of the file. -Please note that if you run an external modem you must specify a speed of 0. - -The program is currently setup to run a 4800 baud external modem on port A -and a Kantronics DE-9600 daughter board on port B so if you have this (or -something similar) then you're right. - -To compile in the driver, put the files in the correct place and patch in -the diff. You will have to re-configure the kernel again before you -recompile it. - -The driver is not real good at the moment for finding the card. You can -'help' it by changing the order of the potential addresses in the structure -found in the pt_init() function so the address of where the card is is put -first. - -After compiling, you have to get them going, they are pretty well like any -other net device and just need ifconfig to get them going. -As an example, here is my /etc/rc.net --------------------------- - -# -# Configure the PackeTwin, port A. -/sbin/ifconfig pt0a 44.136.8.87 hw ax25 vk2xlz mtu 512 -/sbin/ifconfig pt0a 44.136.8.87 broadcast 44.136.8.255 netmask 255.255.255.0 -/sbin/route add -net 44.136.8.0 netmask 255.255.255.0 dev pt0a -/sbin/route add -net 44.0.0.0 netmask 255.0.0.0 gw 44.136.8.68 dev pt0a -/sbin/route add -net 138.25.16.0 netmask 255.255.240.0 dev pt0a -/sbin/route add -host 44.136.8.255 dev pt0a -# -# Configure the PackeTwin, port B. -/sbin/ifconfig pt0b 44.136.8.87 hw ax25 vk2xlz-1 mtu 512 -/sbin/ifconfig pt0b 44.136.8.87 broadcast 44.255.255.255 netmask 255.0.0.0 -/sbin/route add -host 44.136.8.216 dev pt0b -/sbin/route add -host 44.136.8.95 dev pt0b -/sbin/route add -host 44.255.255.255 dev pt0b - -This version of the driver comes under the GNU GPL. If you have one of my -previous (non-GPL) versions of the driver, please update to this one. - -I hope that this all works well for you. I would be pleased to hear how -many people use the driver and if it does its job. - - - Craig vk2xlz <csmall@small.dropbear.id.au> - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |