lkml.org 
[lkml]   [2006]   [Oct]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
SubjectRe: Ordering between PCI config space writes and MMIO reads?
Date

----- Original Message -----
From: "Michael S. Tsirkin" <mst@mellanox.co.il>
To: "Roland Dreier" <rdreier@cisco.com>
Cc: <linux-kernel@vger.kernel.org>; <linux-ia64@vger.kernel.org>;
<jeff@garzik.org>; <matthew@wil.cx>; <openib-general@openib.org>;
<linux-pci@atrey.karlin.mff.cuni.cz>; "David Miller" <davem@davemloft.net>
Sent: Tuesday, October 31, 2006 2:53 PM
Subject: Re: Ordering between PCI config space writes and MMIO reads?


> Quoting r. Roland Dreier <rdreier@cisco.com>:
>> Subject: Re: Ordering between PCI config space writes and MMIO reads?
>>
>> The discussion fizzled out without really reaching a definitive
>> answer, so I'm going to apply the original patch (below), since I
>> pretty much convinced myself that only the driver doing the config
>> access has enough information to fix this reliably.
>>
>> - R.
>>
>> Author: John Partridge <johnip@sgi.com>
>> Date: Tue Oct 31 11:00:04 2006 -0800
>>
>> IB/mthca: Make sure all PCI config writes reach device before doing
>> MMIO
>>
>> During initialization, mthca writes some PCI config space registers
>> and then does an MMIO read from one of the BARs it just enabled.
>> This
>> MMIO read sometimes failed and caused a crash on SGI Altix machines,
>> because the PCI-X host bridge (legitimately, according to the PCI
>> spec) allowed the MMIO read to start before the config write
>> completed.
>>
>> To fix this, add a config read after all config writes to make sure
>> they are all done before starting the MMIO read.
>>
>> Signed-off-by: John Partridge <johnip@sgi.com>
>> Signed-off-by: Roland Dreier <rolandd@cisco.com>
>>
>> diff --git a/drivers/infiniband/hw/mthca/mthca_reset.c
>> b/drivers/infiniband/hw/mthca/mthca_reset.c
>> index 91934f2..578dc7c 100644
>> --- a/drivers/infiniband/hw/mthca/mthca_reset.c
>> +++ b/drivers/infiniband/hw/mthca/mthca_reset.c
>> @@ -281,6 +281,20 @@ good:
>> goto out;
>> }
>>
>> + /*
>> + * Perform a "flush" of the PCI config writes here by reading
>> + * the PCI_COMMAND register. This is needed to make sure that
>> + * we don't try to touch other PCI BARs before the config
>> + * writes are done -- otherwise an MMIO cycle could start
>> + * before the config writes are done and reach the HCA before
>> + * the BAR is actually enabled.
>> + */
>> + if (pci_read_config_dword(mdev->pdev, PCI_COMMAND, hca_header)) {
>> + err = -ENODEV;
>> + mthca_err(mdev, "Couldn't access HCA memory after restoring, "
>> + "aborting.\n");
>> + }
>> +
>> out:
>> if (bridge)
>> pci_dev_put(bridge);
>
> Here's what I don't understand: according to PCI rules, pci config read
> can bypass pci config write (both are non-posted).
> So why does doing it help flush the writes as the comment claims?
>
> Isn't this more the case of
> /* pci_config_write seems to complete asynchronously on Altix systems.
> * This is probably broken but its not clear what's the best
> * thing to do is - for now, do pci_read_config_dword which seems to flush
> * everything out. */
>

If you write to the PCI bus and then you read the result, the read __might__
be the
read that flushes any posted writes rather than the read of device registers
that
would occur after the BARs were configured (hardware may be slower than
the CPU). So, it's best to do the required configuration cycles first, then
after
all is done, read something before you actually need to use data from
subsequent
read/write cycles.

> --
> MST
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/

Cheers,
Dick Johnson
Penguin : Linux version 2.6.16.24 (somewhere)
New Book: http://www.AbominableFirebug.com


-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
\
 
 \ /
  Last update: 2006-10-31 21:39    [W:0.675 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site