Messages in this thread | | | Date | Tue, 31 Jan 2006 16:50:28 -0800 | From | "Randy.Dunlap" <> | Subject | Re: 2.6.16-rc1-mm4 |
| |
On Tue, 31 Jan 2006 14:01:07 -0800 Andrew Morton wrote:
> Al Boldi <a1426z@gawab.com> wrote: > > > > Andrew Morton wrote: > > > Al Boldi <a1426z@gawab.com> wrote: > > > > Andrew Morton wrote: > > > > > - Various other random bits and pieces. Things have been pretty quiet > > > > > lately - most activity seems to be concentrated about putting bugs > > > > > into the various subsystem trees. > > > > > > > > Does it fix the DRM_i810 hang during a suspend-to-ram/disk cycle? > > > > > > I don't know - I don't watch every patch which goes into 49 different > > > trees. Did you try it? > > > > It still hangs w/ drm. > > > > w/o drm STD works like a charm. > > OK. > > > w/o drm STR works lest this t/o and a noisy display in X. > > What do "lest" and "t/o" mean? Please use less abbreviations.
"lest" seems to be a real word... maybe a bit dated.
t/o is 'timeout'.
> > Stopping tasks: ========================| > > Suspending device 0.1 > > Suspending device 0.0 > > Suspending device ide0 > > Suspending device floppy.0 > > Suspending device serio1 > > Suspending device serio0 > > Suspending device i8042 > > Suspending device 0000:01:0a.0 > > Suspending device 0000:01:05.0 > > Suspending device 0000:00:1f.2 > > Suspending device 0000:00:1f.1 > > Suspending device 0000:00:1f.0 > > Suspending device 0000:00:1e.0 > > Suspending device 0000:00:01.0 > > Suspending device 0000:00:00.0 > > Suspending device pci0000:00 > > Suspending device platform > > Intel machine check architecture supported. > > Intel machine check reporting enabled on CPU#0. > > Back to C! > > ACPI: PCI Interrupt 0000:00:01.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> > > IRQ 11 > > PCI: Setting latency timer of device 0000:00:1e.0 to 64 > > eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 > > hda: drive not ready on wakeup > > hda: status timeout: status=0xd0 { Busy } > > ide: failed opcode was: unknown > > hda: DMA disabled > > hdb: DMA disabled > > hda: drive not ready for command > > ide0: reset: success > > BUG: warning at drivers/ide/ide-iops.c:1235/ide_wait_not_busy() > > <c02612e2> ide_wait_not_busy+0xa2/0xb0 <c025ee87> > > start_request+0x1a7/0x230 > > <c025f17a> ide_do_request+0x23a/0x3c0 <c026440a> > > set_multmode_intr+0x1a/0x70 > > <c025f79b> ide_intr+0xeb/0x130 <c02643f0> set_multmode_intr+0x0/0x70 > > <c0135610> handle_IRQ_event+0x30/0x70 <c01356a5> __do_IRQ+0x55/0xc0 > > <c0105672> do_IRQ+0x42/0x70 > > ======================= > > <c0103976> common_interrupt+0x1a/0x20 <c021886d> > > acpi_processor_idle+0x2b6/0x332 > > <c0101030> default_idle+0x0/0x70 <c0101118> cpu_idle+0x58/0x70 > > <c03c47bd> start_kernel+0x14d/0x170 <c03c4310> > > unknown_bootoption+0x0/0x1e0 > > hdb: set_drive_speed_status: status=0x40 { DriveReady } > > ide: failed opcode was: unknown > > Restarting tasks... done > > The above is an IDE problem. Are you saying that the above only occurs > when DRM is enabled? > > Please take more time and use more words when describing this problem, thanks. > > > Also, a 100HZ recompile in mainline causes a 400% delay doing a simple lilo, > > which seems fixed in mm. Is there a reason you can't move that to mainline? > > Again, I don't understand what that means. Are you saying that a kernel > compiled with HZ=100 takes 4 times as long to run lilo?
--- ~Randy - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |