Messages in this thread | | | From | Al Boldi <> | Subject | Re: 2.6.16-rc1-mm4 | Date | Tue, 31 Jan 2006 18:56:13 +0300 |
| |
Andrew Morton wrote: > Al Boldi <a1426z@gawab.com> wrote: > > Andrew Morton wrote: > > > - Various other random bits and pieces. Things have been pretty quiet > > > lately - most activity seems to be concentrated about putting bugs > > > into the various subsystem trees. > > > > Does it fix the DRM_i810 hang during a suspend-to-ram/disk cycle? > > I don't know - I don't watch every patch which goes into 49 different > trees. Did you try it?
It still hangs w/ drm.
w/o drm STD works like a charm. w/o drm STR works lest this t/o and a noisy display in X.
Stopping tasks: ========================| Suspending device 0.1 Suspending device 0.0 Suspending device ide0 Suspending device floppy.0 Suspending device serio1 Suspending device serio0 Suspending device i8042 Suspending device 0000:01:0a.0 Suspending device 0000:01:05.0 Suspending device 0000:00:1f.2 Suspending device 0000:00:1f.1 Suspending device 0000:00:1f.0 Suspending device 0000:00:1e.0 Suspending device 0000:00:01.0 Suspending device 0000:00:00.0 Suspending device pci0000:00 Suspending device platform Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Back to C! ACPI: PCI Interrupt 0000:00:01.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1e.0 to 64 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 hda: drive not ready on wakeup hda: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hda: DMA disabled hdb: DMA disabled hda: drive not ready for command ide0: reset: success BUG: warning at drivers/ide/ide-iops.c:1235/ide_wait_not_busy() <c02612e2> ide_wait_not_busy+0xa2/0xb0 <c025ee87> start_request+0x1a7/0x230 <c025f17a> ide_do_request+0x23a/0x3c0 <c026440a> set_multmode_intr+0x1a/0x70 <c025f79b> ide_intr+0xeb/0x130 <c02643f0> set_multmode_intr+0x0/0x70 <c0135610> handle_IRQ_event+0x30/0x70 <c01356a5> __do_IRQ+0x55/0xc0 <c0105672> do_IRQ+0x42/0x70 ======================= <c0103976> common_interrupt+0x1a/0x20 <c021886d> acpi_processor_idle+0x2b6/0x332 <c0101030> default_idle+0x0/0x70 <c0101118> cpu_idle+0x58/0x70 <c03c47bd> start_kernel+0x14d/0x170 <c03c4310> unknown_bootoption+0x0/0x1e0 hdb: set_drive_speed_status: status=0x40 { DriveReady } ide: failed opcode was: unknown Restarting tasks... done
Also, a 100HZ recompile in mainline causes a 400% delay doing a simple lilo, which seems fixed in mm. Is there a reason you can't move that to mainline?
Thanks!
-- Al
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |