Messages in this thread | | | Date | Sun, 9 May 2004 16:03:11 +0300 (EEST) | From | Meelis Roos <> | Subject | 2.4.26: ACPI error messages on Intel S875WP1-E mainboard |
| |
I get the following ACPI error messages on Intel S875WP1-E mainboard with stock Linux 2.4.26. 2.4.27-pre2 gives the same errors. 2.6.6-rc3-bk10 doesn't give any errors, although it also has the 20040326 ACPI release.
ACPI-1133: *** Error: Method execution failed [\GPRW] (Node f7e70400), AE_NOT_EXIST ACPI-1133: *** Error: Method execution failed [\_SB_.PCI0.P0P2.TANA._PRW] (Node f7e70d80), AE_NOT_EXIST ACPI-0154: *** Error: Method execution failed [\_SB_.PCI0.P0P2.TANA._PRW] (Node f7e70d80), AE_NOT_EXIST
These messages do not seem to disturb anything, the computer is running fine.
And this is the full dmesg:
Linux version 2.4.26-elevant1 (mroos@uusvant) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 SMP Sun May 9 13:13:57 EEST 2004 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003fe30000 (usable) BIOS-e820: 000000003fe30000 - 000000003fe414aa (ACPI NVS) BIOS-e820: 000000003fe414aa - 000000003ff30000 (usable) BIOS-e820: 000000003ff30000 - 000000003ff40000 (ACPI data) BIOS-e820: 000000003ff40000 - 000000003fff0000 (ACPI NVS) BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved) BIOS-e820: 00000000fecf0000 - 00000000fecf1000 (reserved) BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved) Warning only 896MB will be used. Use a HIGHMEM enabled kernel. 896MB LOWMEM available. found SMP MP-table at 000ff780 hm, page 000ff000 reserved twice. hm, page 00100000 reserved twice. hm, page 000fc000 reserved twice. hm, page 000fd000 reserved twice. On node 0 totalpages: 229376 zone(0): 4096 pages. zone(1): 225280 pages. zone(2): 0 pages. ACPI: RSDP (v000 ACPIAM ) @ 0x000f61a0 ACPI: RSDT (v001 INTEL S875PWP4 0x20040205 MSFT 0x00000097) @ 0x3ff30000 ACPI: FADT (v002 INTEL S875PWP4 0x20040205 MSFT 0x00000097) @ 0x3ff30200 ACPI: MADT (v001 INTEL S875PWP4 0x20040205 MSFT 0x00000097) @ 0x3ff30300 ACPI: WDDT (v001 INTEL OEMWDDT 0x00000001 MSFT 0x0100000d) @ 0x3ff345c0 ACPI: DSDT (v001 INTEL S875PWP4 0x00000001 MSFT 0x0100000d) @ 0x00000000 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 Pentium 4(tm) XEON(tm) APIC version 20 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 Pentium 4(tm) XEON(tm) APIC version 20 ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0]) IOAPIC[0]: Assigned apic_id 2 IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, IRQ 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) Using ACPI (MADT) for SMP configuration information Kernel command line: auto BOOT_IMAGE=Linux ro root=900 Initializing CPU#0 Detected 2793.073 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 5570.56 BogoMIPS Memory: 904528k/917504k available (1468k kernel code, 12588k reserved, 610k data, 128k init, 0k highmem) Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode cache hash table entries: 65536 (order: 7, 524288 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 65536 (order: 6, 262144 bytes) Page-cache hash table entries: 262144 (order: 8, 1048576 bytes) CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Physical Processor ID: 0 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: bfebfbff 00000000 00000000 00000000 CPU: Common caps: bfebfbff 00000000 00000000 00000000 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au) mtrr: detected mtrr type: Intel CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Physical Processor ID: 0 Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: bfebfbff 00000000 00000000 00000000 CPU: Common caps: bfebfbff 00000000 00000000 00000000 CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09 per-CPU timeslice cutoff: 1462.56 usecs. enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Booting processor 1/1 eip 3000 Initializing CPU#1 masked ExtINT on CPU#1 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Calibrating delay loop... 5583.66 BogoMIPS CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Physical Processor ID: 0 Intel machine check reporting enabled on CPU#1. CPU: After generic, caps: bfebfbff 00000000 00000000 00000000 CPU: Common caps: bfebfbff 00000000 00000000 00000000 CPU1: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09 Total of 2 processors activated (11154.22 BogoMIPS). cpu_sibling_map[0] = 1 cpu_sibling_map[1] = 0 ENABLING IO-APIC IRQs init IO_APIC IRQs IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected. ..TIMER: vector=0x31 pin1=2 pin2=-1 Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 2793.1070 MHz. ..... host bus clock speed is 199.5075 MHz. cpu: 0, clocks: 1995075, slice: 665025 CPU0<T0:1995072,T1:1330016,D:31,S:665025,C:1995075> cpu: 1, clocks: 1995075, slice: 665025 CPU1<T0:1995072,T1:665008,D:14,S:665025,C:1995075> checking TSC synchronization across CPUs: passed. Waiting on wait_init_idle (map = 0x2) All processors have done init_idle ACPI: Subsystem revision 20040326 PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=3 PCI: Using configuration type 1 ACPI-1133: *** Error: Method execution failed [\GPRW] (Node f7e70400), AE_NOT_EXIST ACPI-1133: *** Error: Method execution failed [\_SB_.PCI0.P0P2.TANA._PRW] (Node f7e70d80), AE_NOT_EXIST ACPI-0154: *** Error: Method execution failed [\_SB_.PCI0.P0P2.TANA._PRW] (Node f7e70d80), AE_NOT_EXIST ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: System [ACPI] (supports S0 S1 S4 S5) ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 00:1f.1 Transparent bridge - Intel Corp. 82801BA/CA/DB/EB PCI Bridge ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT] ACPI: Power Resource [URP1] (off) ACPI: Power Resource [URP2] (off) ACPI: Power Resource [FDDP] (off) ACPI: Power Resource [LPTP] (off) ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 *12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 14 15) PCI: Probing PCI hardware IOAPIC[0]: Set PCI routing entry (2-16 -> 0xa9 -> IRQ 16 Mode:1 Active:1) 00:00:02[A] -> 2-16 -> IRQ 16 IOAPIC[0]: Set PCI routing entry (2-17 -> 0xb1 -> IRQ 17 Mode:1 Active:1) 00:00:1f[B] -> 2-17 -> IRQ 17 IOAPIC[0]: Set PCI routing entry (2-18 -> 0xb9 -> IRQ 18 Mode:1 Active:1) 00:00:1f[A] -> 2-18 -> IRQ 18 IOAPIC[0]: Set PCI routing entry (2-19 -> 0xc1 -> IRQ 19 Mode:1 Active:1) 00:00:1d[B] -> 2-19 -> IRQ 19 IOAPIC[0]: Set PCI routing entry (2-23 -> 0xc9 -> IRQ 23 Mode:1 Active:1) 00:00:1d[D] -> 2-23 -> IRQ 23 IOAPIC[0]: Set PCI routing entry (2-20 -> 0xd1 -> IRQ 20 Mode:1 Active:1) 00:03:08[A] -> 2-20 -> IRQ 20 IOAPIC[0]: Set PCI routing entry (2-21 -> 0xd9 -> IRQ 21 Mode:1 Active:1) 00:03:00[A] -> 2-21 -> IRQ 21 IOAPIC[0]: Set PCI routing entry (2-22 -> 0xe1 -> IRQ 22 Mode:1 Active:1) 00:03:00[B] -> 2-22 -> IRQ 22 number of MP IRQ sources: 15. number of IO-APIC #2 registers: 24. testing the IO APIC.......................
IO APIC #2...... .... register #00: 02000000 ....... : physical APIC id: 02 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00178020 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0020 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 003 03 0 0 0 0 0 1 1 39 02 003 03 0 0 0 0 0 1 1 31 03 003 03 0 0 0 0 0 1 1 41 04 003 03 0 0 0 0 0 1 1 49 05 003 03 0 0 0 0 0 1 1 51 06 003 03 0 0 0 0 0 1 1 59 07 003 03 0 0 0 0 0 1 1 61 08 003 03 0 0 0 0 0 1 1 69 09 003 03 0 1 0 0 0 1 1 71 0a 003 03 0 0 0 0 0 1 1 79 0b 003 03 0 0 0 0 0 1 1 81 0c 003 03 0 0 0 0 0 1 1 89 0d 003 03 0 0 0 0 0 1 1 91 0e 003 03 0 0 0 0 0 1 1 99 0f 003 03 0 0 0 0 0 1 1 A1 10 003 03 1 1 0 1 0 1 1 A9 11 003 03 1 1 0 1 0 1 1 B1 12 003 03 1 1 0 1 0 1 1 B9 13 003 03 1 1 0 1 0 1 1 C1 14 003 03 1 1 0 1 0 1 1 D1 15 003 03 1 1 0 1 0 1 1 D9 16 003 03 1 1 0 1 0 1 1 E1 17 003 03 1 1 0 1 0 1 1 C9 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ10 -> 0:10 IRQ11 -> 0:11 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 IRQ16 -> 0:16 IRQ17 -> 0:17 IRQ18 -> 0:18 IRQ19 -> 0:19 IRQ20 -> 0:20 IRQ21 -> 0:21 IRQ22 -> 0:22 IRQ23 -> 0:23 .................................... done. PCI: Using ACPI for IRQ routing PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off' Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd VFS: Disk quotas vdquot_6.5.1 Journalled Block Device driver loaded ACPI: Power Button (FF) [PWRF] ACPI: Sleep Button (CM) [SLPB] ACPI: Processor [CPU1] (supports C1, 8 throttling states) ACPI: Processor [CPU2] (supports C1, 8 throttling states) Detected PS/2 Mouse Port. pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ DETECT_IRQ SERIAL_PCI enabled keyboard: Timeout - AT keyboard not present?(ed) keyboard: Timeout - AT keyboard not present?(f4) ttyS00 at 0x03f8 (irq = 4) is a 16550A Real Time Clock Driver v1.10f Non-volatile memory driver v1.2 i810_rng hardware driver 0.9.8 loaded hw_random: misc device register failed i810 TCO timer, v0.05: timer margin: 30 sec (0x0460) (nowayout=0) Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 NET4: Frame Diverter 0.46 Intel(R) PRO/1000 Network Driver - version 5.2.30.1-k1 Copyright (c) 1999-2004 Intel Corporation. PCI: Setting latency timer of device 02:01.0 to 64 divert: allocating divert_blk for eth0 eth0: Intel(R) PRO/1000 Network Connection Intel(R) PRO/100 Network Driver - version 2.3.38-k1 Copyright (c) 2004 Intel Corporation
divert: allocating divert_blk for eth1 e100: selftest OK. e100: eth1: Intel(R) PRO/100 Network Connection Hardware receive checksums enabled
Linux agpgart interface v0.99 (c) Jeff Hartmann agpgart: Maximum main memory to use for agp memory: 816M agpgart: Unsupported Intel chipset (device id: 2578), you might want to boot with agp=try_unsupported agpgart: no supported devices found. Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH5: IDE controller at PCI slot 00:1f.1 PCI: Enabling device 00:1f.1 (0005 -> 0007) ICH5: chipset revision 2 ICH5: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio ICH5-SATA: IDE controller at PCI slot 00:1f.2 ICH5-SATA: chipset revision 2 ICH5-SATA: 100% native mode on irq 18 ide2: BM-DMA at 0xdc00-0xdc07, BIOS settings: hde:DMA, hdf:pio ide3: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdg:DMA, hdh:pio hdc: SAMSUNG CD-ROM SC-152A, ATAPI CD/DVD-ROM drive hde: WDC WD800JD-00HKA0, ATA DISK drive hdf: probing with STATUS(0x00) instead of ALTSTATUS(0x50) hdf: probing with STATUS(0x00) instead of ALTSTATUS(0x50) blk: queue c0380f78, I/O limit 4095Mb (mask 0xffffffff) hdg: WDC WD800JD-00HKA0, ATA DISK drive hdh: probing with STATUS(0x00) instead of ALTSTATUS(0x50) hdh: probing with STATUS(0x00) instead of ALTSTATUS(0x50) blk: queue c03813e4, I/O limit 4095Mb (mask 0xffffffff) ide1 at 0x170-0x177,0x376 on irq 15 ide2 at 0xec00-0xec07,0xe802 on irq 18 ide3 at 0xe400-0xe407,0xe002 on irq 18 hde: attached ide-disk driver. hde: host protected area => 1 hde: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/16/63, UDMA(33) hdg: attached ide-disk driver. hdg: host protected area => 1 hdg: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/16/63, UDMA(33) hdc: attached ide-cdrom driver. hdc: ATAPI 52X CD-ROM drive, 128kB Cache, DMA Uniform CD-ROM driver Revision: 3.12 Partition check: hde: hde1 hde2 hde3 hdg: hdg1 hdg2 hdg3 Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found mice: PS/2 mouse device common for all mice md: linear personality registered as nr 1 md: raid0 personality registered as nr 2 md: raid1 personality registered as nr 3 md: raid5 personality registered as nr 4 raid5: measuring checksumming speed 8regs : 3201.600 MB/sec 32regs : 2496.000 MB/sec pIII_sse : 3653.200 MB/sec pII_mmx : 3238.800 MB/sec p5_mmx : 3347.600 MB/sec raid5: using function: pIII_sse (3653.200 MB/sec) md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: Autodetecting RAID arrays. [events: 00128d3b] [events: 000270f7] [events: 00128d3b] [events: 000270f7] md: autorun ... md: considering hdg3 ... md: adding hdg3 ... md: adding hde3 ... md: created md1 md: bind<hde3,1> md: bind<hdg3,2> md: running: <hdg3><hde3> md: hdg3's event counter: 000270f7 md: hde3's event counter: 000270f7 md: md1: raid array is not clean -- starting background reconstruction md: RAID level 1 does not need chunksize! Continuing anyway. md1: max total readahead window set to 124k md1: 1 data-disks, max readahead per data-disk: 124k raid1: device hdg3 operational as mirror 1 raid1: device hde3 operational as mirror 0 raid1: raid set md1 not clean; reconstructing mirrors raid1: raid set md1 active with 2 out of 2 mirrors md: syncing RAID array md1 md: minimum _guaranteed_ reconstruction speed: 100 KB/sec/disc. md: using maximum available idle IO bandwith (but not more than 100000 KB/sec) for reconstruction. md: using 124k window, over a total of 54713664 blocks. md: updating md1 RAID superblock on device md: hdg3 [events: 000270f8]<6>(write) hdg3's sb offset: 54713664 md: hde3 [events: 000270f8]<6>(write) hde3's sb offset: 54713664 md: considering hdg1 ... md: adding hdg1 ... md: adding hde1 ... md: created md0 md: bind<hde1,1> md: bind<hdg1,2> md: running: <hdg1><hde1> md: hdg1's event counter: 00128d3b md: hde1's event counter: 00128d3b md: md0: raid array is not clean -- starting background reconstruction md: RAID level 1 does not need chunksize! Continuing anyway. md0: max total readahead window set to 124k md0: 1 data-disks, max readahead per data-disk: 124k raid1: device hdg1 operational as mirror 1 raid1: device hde1 operational as mirror 0 raid1: raid set md0 not clean; reconstructing mirrors raid1: raid set md0 active with 2 out of 2 mirrors md: delaying resync of md0 until md1 has finished resync (they share one or more physical units) md: updating md0 RAID superblock on device md: hdg1 [events: 00128d3c]<6>(write) hdg1's sb offset: 19530880 md: hde1 [events: 00128d3c]<6>(write) hde1's sb offset: 19530880 md: ... autorun DONE. Initializing Cryptographic API NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 8192 buckets, 64Kbytes TCP: Hash tables configured (established 262144 bind 65536) Linux IP multicast router 0.06 plus PIM-SM NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. kjournald starting. Commit interval 5 seconds EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 128k freed Adding Swap: 2097136k swap-space (priority -1) Adding Swap: 2097136k swap-space (priority -2) SCSI subsystem driver Revision: 1.00 EXT3 FS 2.4-0.9.19, 19 August 2002 on md(9,0), internal journal usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb-uhci.c: $Revision: 1.275 $ time 13:17:23 May 9 2004 usb-uhci.c: High bandwidth mode enabled PCI: Setting latency timer of device 00:1d.0 to 64 usb-uhci.c: USB UHCI at I/O 0xcc00, IRQ 16 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected PCI: Setting latency timer of device 00:1d.1 to 64 usb-uhci.c: USB UHCI at I/O 0xd000, IRQ 19 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 2 ports detected PCI: Setting latency timer of device 00:1d.2 to 64 usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 18 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 3 hub.c: USB hub found hub.c: 2 ports detected PCI: Setting latency timer of device 00:1d.3 to 64 usb-uhci.c: USB UHCI at I/O 0xd800, IRQ 16 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 4 hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: v1.275:USB Universal Host Controller Interface driver usb.c: registered new driver hiddev usb.c: registered new driver hid hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz> hid-core.c: USB HID support drivers kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on md(9,1), internal journal EXT3-fs: mounted filesystem with ordered data mode. PCI: Setting latency timer of device 00:1d.7 to 64 ehci_hcd 00:1d.7: Intel Corp. 82801EB USB2 ehci_hcd 00:1d.7: irq 23, pci mem f8a72c00 usb.c: new USB bus registered, assigned bus number 5 ehci_hcd 00:1d.7: enabled 64bit PCI DMA PCI: cache line size of 128 is not supported by device 00:1d.7 ehci_hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4 hub.c: USB hub found hub.c: 8 ports detected e1000: eth0 NIC Link is Up 100 Mbps Full Duplex parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE] parport0: irq 7 detected lp0: using parport0 (polling). md: md1: sync done. md: syncing RAID array md0 md: minimum _guaranteed_ reconstruction speed: 100 KB/sec/disc. md: using maximum available idle IO bandwith (but not more than 100000 KB/sec) for reconstruction. md: using 124k window, over a total of 19530880 blocks. md: md0: sync done.
-- Meelis Roos (mroos@linux.ee)
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |