Messages in this thread | ![/](/images/icornerl.gif) | | Date | Tue, 15 Jul 2003 13:59:17 -0700 (PDT) | From | crozierm@consumpt ... | Subject | USB mouse "hang" with 2.5.75 |
| |
Hello,
I'm experiencing odd USB mouse behaviour with 2.5.75 & 2.6.0-test1. Those are the only 2.5.x flavors I've used on this particular computer, so I don't know if this is something new.
While using the mouse normally, it will suddenly stop responding. If I cat /dev/input/mice and wiggle the mouse, nothing is returned. No extra debug messages appear in the syslog until I unplug the mouse and plug it back it, at which point everything works normally. I can't find specific steps to reproduce it, but with persistent use I can usually get it to hang up within a minute or two.
Also, if I leave XFree86 and go to the console, then switch back to XFree86, the mouse is restored. Because of this I thought it must be X, but this has never happened with 2.4.x.
Below is usb debug logging and system info. If I can provide any other information, please respond to me directly, as I'm not on the list.
-Michael
The mouse is a logitech optical usb mouse. More info below in the usb logging.
USB info:
00:1d.0 USB Controller: Intel Corp. 82801DB USB (Hub #1) (rev 01) 00:1d.1 USB Controller: Intel Corp. 82801DB USB (Hub #2) (rev 01) 00:1d.2 USB Controller: Intel Corp. 82801DB USB (Hub #3) (rev 01) 00:1d.7 USB Controller: Intel Corp. 82801DB USB EHCI Controller (rev 01)
Syslog debugging when I unplug:
ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001002 POWER sig=se0 CSC hub 1-0:0: port 5, status 100, change 1, 12 Mb/s hub 4-0:0: port 1, status 100, change 3, 12 Mb/s usb 4-1: USB disconnect, address 5 usb 4-1: unregistering interfaces usb 4-1: hcd_unlink_urb f72ced00 fail -22 usb 4-1: hcd_unlink_urb f72ce680 fail -22 usb 4-1: unregistering device hub 4-0:0: port 1 enable change, status 100 drivers/usb/host/uhci-hcd.c: ff40: suspend_hc
syslogging when I plug back in:
ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001403 POWER sig=k CSC CONNECT hub 1-0:0: port 5, status 501, change 1, 480 Mb/s hub 1-0:0: debounce: port 5: delay 100ms stable 4 status 0x501 ehci_hcd 0000:00:1d.7: port 5 low speed --> companion ehci_hcd 0000:00:1d.7: GetStatus port 5 status 003002 POWER OWNER sig=se0 CSC drivers/usb/host/uhci-hcd.c: ff40: wakeup_hc hub 4-0:0: port 1, status 301, change 1, 1.5 Mb/s hub 4-0:0: debounce: port 1: delay 100ms stable 4 status 0x301 hub 4-0:0: new USB device on port 1, assigned address 6 usb 4-1: new device strings: Mfr=1, Product=2, SerialNumber=0 usb 4-1: Product: USB Optical Mouse usb 4-1: Manufacturer: Logitech usb 4-1: usb_new_device - registering interface 4-1:0 hid 4-1:0: usb_device_probe hid 4-1:0: usb_device_probe - got id input: USB HID v1.10 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.2-1
Other system info:
Intel E7505 w/ xeon
Linux version 2.6.0-test1 (crozierm@dentaku) (gcc version 3.3.1 20030626 (Debian prerelease)) #6 SMP Tue Jul 15 12:12:40 PDT 2003
--
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| ![\](/images/icornerr.gif) |