Messages in this thread | | | Date | Wed, 02 Jul 2003 04:01:26 +0200 | From | Christian Kujau <> | Subject | scsi timeout with 2.4 |
| |
hi,
i don't know if it is a kernel issue at all, it could be a hardware issue too, but i can't tell so please have a look.
i am using linux 2.4.20 on a PowerPC (PReP) with a "LSI Logic / Symbios Logic (formerly NCR) 53c825 (rev 13)" scsi controller (onboard). i am using the symbios driver (CONFIG_SCSI_SYM53C8XX) because the other alternatives (NCR53C8XX, timeouts during boot, booting stops. SYM53C8XX_2, timeouts during use, unuseable) are not working.
i have these timouts when there is heavy traffic on the controller, it's reproduceable, it happens only *sometimes* during "normal" use. when these timeouts occur, load goes up to 10-16, the system is unuseable, then, after a few seconds, the system status seems to be ok again, load is going down to normal.
i know, the controller and the machine is a bit old, but it serves my needs. on the controller there are 3 scsi disks (2x18 GB IBM xServer, 1x36GB eServer -- yes High-End scsi disks on a low-end controller, but the disks were cheap, somehow.)
here are the timeouts:
scsi : aborting command due to timeout : pid 3463623, scsi0, channel 0,\ id 1, lun 0 Read (10) 00 01 d0 1e 9a 00 01 00 00 sym53c8xx_abort: pid=3463623 serial_number=3463623 serial_number_at_timeout=3463623 SCSI host 0 abort (pid 3463623) timed out - resetting SCSI bus is being reset for host 0 channel 0. sym53c8xx_reset: pid=3463623 reset_flags=2 serial_number=3463623\ serial_number_at_timeout=3463623 sym53c825a-0-<0,*>: FAST-10 WIDE SCSI 20.0 MB/s (100.0 ns, offset 8) sym53c825a-0-<1,*>: FAST-10 WIDE SCSI 20.0 MB/s (100.0 ns, offset 8) sym53c825a-0-<2,*>: FAST-10 WIDE SCSI 20.0 MB/s (100.0 ns, offset 8)
the first line ("scsi: abort...") is sometimes repeated, 2 or up to 7 times. the last 3 lines are always repeated 3 times, as you can see above. and the "id" is not always "1" but all three id's are affected. while i don't believe that the disks are bad, i suspect the scsi controller perhaps, or is it a driver issue and can i tune something? the driver is statically compiled into the kernel with default settings. (DEFAULT_TAGS=8, MAX_TAGS=32, SYNC=20).
what is your opinion on that? the controller, the disks (perhaps too new for the controller?) or the driver?
Thank you for your time, Christian.
root@sheep:~# cat /proc/scsi/sym53c8xx/0 General information: Chip sym53c825a, device id 0x3, revision id 0x13 On PCI bus 0, device 12, function 0, IRQ 15 Synchronous period factor 25, max commands per lun 32 root@sheep:~# root@sheep:~# cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: IBM-ESXS Model: ST318305LW !# Rev: B245 Type: Direct-Access ANSI SCSI revision: 03 Host: scsi0 Channel: 00 Id: 01 Lun: 00 Vendor: IBM-ESXS Model: ST318305LW !# Rev: B244 Type: Direct-Access ANSI SCSI revision: 03 Host: scsi0 Channel: 00 Id: 02 Lun: 00 Vendor: IBM-ESXS Model: ST336607LW FN Rev: B258 Type: Direct-Access ANSI SCSI revision: 03 root@sheep:~# root@sheep:~# cat /proc/cpuinfo cpu : 604r clock : ??? revision : 49.2 (pvr 0009 3102) bogomips : 299.00 machine : PReP Utah (Powerstack II Pro4000) L2 : 512Kb, parity disabled SRAM:synchronous,pipelined,no parity root@sheep:~#
-- BOFH excuse #274:
It was OK before you touched it.
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |