Messages in this thread | | | Date | Fri, 4 Apr 2003 12:34:13 +0200 (CEST) | From | "Erno Rigo [McRee]" <> | Subject | PROBLEM: hpt372 - drive drops out using dma |
| |
Hello!
[1.] hpt372 - driver drops out using dma
[2.] I've just purchased an abit-kd7-raid with an integrated hpt372 controller. I've configured the kernel and experimented the system bios and pci slot order settings many ways - allways with the same result: after few random read accesses (movie or mp3 playing, copying files) my maxtor ide drive simply fails to respond to any read or reset requests. When i disable dma with hdparm -d0, the problem disappears, but that's a bit expensive workaround. The system is working good with the 'official' hpt372 generic scsi driver (http://www.highpoint-tech.com/hpt3xx-opensource-v131.tgz), but i cannot totally disable hpt372 recognition during bootup ('HPT372: detected chipset, but driver not compiled in!') witch causes a very slow bootup procedure caused by 'hde: lost interrupt'-s.
[3.] ide, hpt372
[4.] Linux version 2.4.20 (root@mcree) (gcc version 2.95.4 20011002 (Debian prerelease)) #7 2003. ápr. 4., péntek, 11.03.00 CEST
[5.] output of hdparm -I /dev/hde _before_ the dropout: -----8<----------------------------------------------------------------------- /dev/hde:
non-removable ATA device, with non-removable media Model Number: Maxtor 4G120J6 Serial Number: G60AQ60E Firmware Revision: GAK819K0 Standards: Supported: 1 2 3 4 5 6 Likely used: 6 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 bytes/track: 0 (obsolete) bytes/sector: 0 (obsolete) current sector capacity: 16514064 LBA user addressable sectors = 240121728 Capabilities: LBA, IORDY(can be disabled) Buffer size: 2048.0kB ECC bytes: 57 Queue depth: 1 Standby timer values: spec'd by standard, no device specific minimum r/w multiple sector transfer: Max = 16 Current = 16 Advanced power management level: 3 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 udma6 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * NOP cmd * READ BUFFER cmd * WRITE BUFFER cmd * Host Protected Area feature set * look-ahead * write cache * Power Management feature set SMART feature set SET MAX security extension * Advanced Power Management feature set * DOWNLOAD MICROCODE cmd HW reset results: CBLID- above Vih Device num = 0 determined by the jumper Checksum: correct -----8<-----------------------------------------------------------------------
Output of hdparm -I /dev/hde _after_ the dropout: -----8<----------------------------------------------------------------------- /dev/hde:
removable ATA device, with non-removable media Standards: Likely used: 1 Configuration: Logical max current cylinders heads sectors/track bytes/track: bytes/sector: LBA user addressable sectors = 0 Capabilities: no IORDY Cannot perform double-word IO r/w multiple sector transfer: not supported DMA: not supported PIO: pio0 -----8<-----------------------------------------------------------------------
my syslog: -----8<----------------------------------------------------------------------- Apr 4 10:44:22 mcree kernel: hde: dma_intr: status=0xff { Busy } Apr 4 10:44:22 mcree kernel: hde: DMA disabled Apr 4 10:44:57 mcree kernel: ide2: reset timed-out, status=0xff Apr 4 10:44:57 mcree kernel: hde: status timeout: status=0xff { Busy } Apr 4 10:44:57 mcree kernel: hde: drive not ready for command Apr 4 10:45:27 mcree kernel: ide2: reset timed-out, status=0xff Apr 4 10:45:27 mcree kernel: end_request: I/O error, dev 21:05 (hde), sector 58956 Apr 4 10:45:27 mcree kernel: end_request: I/O error, dev 21:05 (hde), sector 61700 Apr 4 10:45:27 mcree kernel: end_request: I/O error, dev 21:05 (hde), sector 61701 Apr 4 10:45:27 mcree kernel: end_request: I/O error, dev 21:05 (hde), sector 61702 Apr 4 10:45:27 mcree kernel: end_request: I/O error, dev 21:05 (hde), sector 61703 [...various errors resulting in 'filesystem panic'...] -----8<-----------------------------------------------------------------------
slow bootup caused by unwanted hpt372 (and attached drive) recognition (i turned off CONFIG_BLK_DEV_HPT34X in order to be able to use the 'official' hpt driver, but i still want to use my primary vt8235 controller) - note the 'lost interrupt'-s and the drive recognition: -----8<----------------------------------------------------------------------- Apr 4 11:36:01 mcree kernel: Uniform Multi-Platform E-IDE driver Revision: 6.31 Apr 4 11:36:01 mcree kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Apr 4 11:36:01 mcree kernel: VP_IDE: IDE controller on PCI bus 00 dev 89 Apr 4 11:36:01 mcree kernel: VP_IDE: chipset revision 6 Apr 4 11:36:01 mcree kernel: VP_IDE: not 100%% native mode: will probe irqs later Apr 4 11:36:01 mcree kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Apr 4 11:36:01 mcree kernel: VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci00:11.1 Apr 4 11:36:01 mcree kernel: ide0: BM-DMA at 0xd400-0xd407, BIOS settings: hda:DMA, hdb:pio Apr 4 11:36:01 mcree kernel: ide1: BM-DMA at 0xd408-0xd40f, BIOS settings: hdc:DMA, hdd:DMA Apr 4 11:36:01 mcree kernel: HPT372: IDE controller on PCI bus 00 dev 98 Apr 4 11:36:01 mcree kernel: HPT372: detected chipset, but driver not compiled in! Apr 4 11:36:01 mcree kernel: HPT372: chipset revision 5 Apr 4 11:36:01 mcree kernel: HPT372: not 100%% native mode: will probe irqs later Apr 4 11:36:01 mcree kernel: ide2: BM-DMA at 0xe800-0xe807, BIOS settings: hde:pio, hdf:pio Apr 4 11:36:01 mcree kernel: ide3: BM-DMA at 0xe808-0xe80f, BIOS settings: hdg:pio, hdh:pio Apr 4 11:36:01 mcree kernel: hda: ST360015A, ATA DISK drive Apr 4 11:36:01 mcree kernel: hdc: ASUS CRW-1610A, ATAPI CD/DVD-ROM drive Apr 4 11:36:01 mcree kernel: hdd: Pioneer DVD-ROM ATAPIModel DVD-106S 012, ATAPI CD/DVD-ROM drive Apr 4 11:36:01 mcree kernel: hde: Maxtor 4G120J6, ATA DISK drive Apr 4 11:36:01 mcree kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Apr 4 11:36:01 mcree kernel: ide1 at 0x170-0x177,0x376 on irq 15 Apr 4 11:36:01 mcree kernel: ide2 at 0xd800-0xd807,0xdc02 on irq 18 Apr 4 11:36:01 mcree kernel: blk: queue c03980c4, I/O limit 4095Mb (mask 0xffffffff) Apr 4 11:36:01 mcree kernel: hda: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=7297/255/63, UDMA(100) Apr 4 11:36:01 mcree kernel: hde: lost interrupt Apr 4 11:36:01 mcree last message repeated 3 times Apr 4 11:36:01 mcree kernel: hde: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=14946/255/63 Apr 4 11:36:01 mcree kernel: Partition check: Apr 4 11:36:01 mcree kernel: /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 > Apr 4 11:36:01 mcree kernel: /dev/ide/host2/bus0/target0/lun0:hde: lost interrupt Apr 4 11:36:01 mcree kernel: hde: lost interrupt Apr 4 11:36:01 mcree kernel: p1 <hde: lost interrupt Apr 4 11:36:01 mcree kernel: p5 > Apr 4 11:36:01 mcree kernel: Floppy drive(s): fd0 is 1.44M Apr 4 11:36:01 mcree kernel: FDC 0 is a post-1991 82077 Apr 4 11:36:01 mcree kernel: loop: loaded (max 8 devices) -----8<-----------------------------------------------------------------------
The 'official' driver works ok. after the above 'slow boot': -----8<----------------------------------------------------------------------- Apr 4 11:36:01 mcree kernel: Device Driver for HPT37x2 ATA RAID Controller Apr 4 11:36:01 mcree kernel: Version 1.31, Compiled Apr 4 2003 10:58:27 Apr 4 11:36:01 mcree kernel: Found Controller: HPT372 UDMA/ATA133 RAID Controller Apr 4 11:36:01 mcree kernel: scsi1 : hpt37x2 Apr 4 11:36:01 mcree kernel: Vendor: Maxtor 4 Model: G120J6 Rev: GAK8 Apr 4 11:36:01 mcree kernel: Type: Direct-Access ANSI SCSI revision: 02 Apr 4 11:36:01 mcree kernel: Attached scsi disk sda at scsi1, channel 0, id 0, lun 0 Apr 4 11:36:01 mcree kernel: SCSI device sda: 240121728 512-byte hdwr sectors (122942 MB) Apr 4 11:36:01 mcree kernel: /dev/scsi/host1/bus0/target0/lun0: p1 < p5 > -----8<-----------------------------------------------------------------------
[6.] It was impossible not to reproduce the problem. 8) The drive functioned properly for a small (but random) amount of time, then crashed.
[7.] [7.1.] If some fields are empty or look unusual you may have an old version. Compare to the current minimal requirements in Documentation/Changes.
Linux mcree 2.4.20 #7 2003. ápr. 4., péntek, 11.03.00 CEST i686 unknown
Gnu C 2.95.4 Gnu make 3.79.1 util-linux 2.11n mount 2.11n modutils 2.4.15 e2fsprogs 1.27 reiserfsprogs 3.x.1b Linux C Library 2.3.1 Dynamic linker (ldd) 2.3.1 Procps 2.0.7 Net-tools 1.60 Console-tools 0.2.3 Sh-utils 2.0.11 Modules Loaded hpt37x2 nvidia
[7.2.] processor : 0 vendor_id : AuthenticAMD cpu family : 6 model : 8 model name : AMD Athlon(tm) XP 2100+ stepping : 1 cpu MHz : 1734.084 cache size : 256 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 1 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse syscall mmxext 3dnowext 3dnow bogomips : 3460.30
[7.3.] hpt37x2 55584 1 nvidia 1546144 10
[7.4.] cat /proc/ioports 0000-001f : dma1 0020-003f : pic1 0040-005f : timer 0060-006f : keyboard 0070-007f : rtc 0080-008f : dma page reg 00a0-00bf : pic2 00c0-00df : dma2 00f0-00ff : fpu 0170-0177 : ide1 01f0-01f7 : ide0 0376-0376 : ide1 0378-037a : parport0 037b-037f : parport0 03c0-03df : vga+ 03f6-03f6 : ide0 03f8-03ff : serial(auto) 0cf8-0cff : PCI conf1 c000-c0ff : Accton Technology Corporation EN-1216 Ethernet Adapter c000-c0ff : tulip c400-c43f : Ensoniq 5880 AudioPCI c400-c43f : es1371 c800-c81f : VIA Technologies, Inc. USB cc00-cc1f : VIA Technologies, Inc. USB (#2) d000-d01f : VIA Technologies, Inc. USB (#3) d400-d40f : VIA Technologies, Inc. VT82C586B PIPC Bus Master IDE d400-d407 : ide0 d408-d40f : ide1 d800-d807 : Triones Technologies, Inc. HPT366/368/370/370A/372 d800-d807 : ide2 dc00-dc03 : Triones Technologies, Inc. HPT366/368/370/370A/372 dc02-dc02 : ide2 e000-e007 : Triones Technologies, Inc. HPT366/368/370/370A/372 e400-e403 : Triones Technologies, Inc. HPT366/368/370/370A/372 e800-e8ff : Triones Technologies, Inc. HPT366/368/370/370A/372 e800-e807 : ide2 e808-e80f : ide3 e810-e8ff : HPT372
cat /proc/iomem 00000000-0009efff : System RAM 0009f000-0009ffff : reserved 000a0000-000bffff : Video RAM area 000c0000-000c7fff : Video ROM 000d0000-000d3bff : Extension ROM 000f0000-000fffff : System ROM 00100000-1ffeffff : System RAM 00100000-0029b44f : Kernel code 0029b450-0031d4f7 : Kernel data 1fff0000-1fff2fff : ACPI Non-volatile Storage 1fff3000-1fffffff : ACPI Tables d0000000-dfffffff : PCI Bus #01 d0000000-d7ffffff : nVidia Corporation NV17 [GeForce4 MX440] d8000000-d807ffff : nVidia Corporation NV17 [GeForce4 MX440] e0000000-e3ffffff : PCI device 1106:3189 (VIA Technologies, Inc.) e4000000-e5ffffff : PCI Bus #01 e4000000-e4ffffff : nVidia Corporation NV17 [GeForce4 MX440] e6020000-e60203ff : Accton Technology Corporation EN-1216 Ethernet Adapter e6020000-e60203ff : tulip e6021000-e6021fff : Brooktree Corporation Bt878 Video Capture e6021000-e6021fff : bttv e6022000-e6022fff : Brooktree Corporation Bt878 Audio Capture e6023000-e60230ff : VIA Technologies, Inc. USB 2.0 fec00000-fec00fff : reserved fee00000-fee00fff : reserved ffff0000-ffffffff : reserved
[7.5.] 00:00.0 Host bridge: VIA Technologies, Inc.: Unknown device 3189 Subsystem: ABIT Computer Corp.: Unknown device 1401 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 8 Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M] Capabilities: [a0] AGP version 2.0 Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2 Command: RQ=31 SBA- AGP+ 64bit- FW- Rate=<none> Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc.: Unknown device b168 (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: e4000000-e5ffffff Prefetchable memory behind bridge: d0000000-dfffffff BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 Ethernet controller: Accton Technology Corporation EN-1216 Ethernet Adapter (rev 11) Subsystem: Standard Microsystems Corp [SMC]: Unknown device 1255 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (63750ns min, 63750ns max), cache line size 08 Interrupt: pin A routed to IRQ 17 Region 0: I/O ports at c000 [size=256] Region 1: Memory at e6020000 (32-bit, non-prefetchable) [size=1K] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=100mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 Multimedia video controller: Brooktree Corporation Bt878 (rev 11) Subsystem: Pinnacle Systems Inc.: Unknown device 0012 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (4000ns min, 10000ns max) Interrupt: pin A routed to IRQ 17 Region 0: Memory at e6021000 (32-bit, prefetchable) [size=4K] Capabilities: [44] Vital Product Data Capabilities: [4c] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.1 Multimedia controller: Brooktree Corporation Bt878 (rev 11) Subsystem: Pinnacle Systems Inc.: Unknown device 0012 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (1000ns min, 63750ns max) Interrupt: pin A routed to IRQ 17 Region 0: Memory at e6022000 (32-bit, prefetchable) [size=4K] Capabilities: [44] Vital Product Data Capabilities: [4c] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.0 Multimedia audio controller: Ensoniq 5880 AudioPCI (rev 02) Subsystem: Ensoniq Creative Sound Blaster AudioPCI128 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (3000ns min, 32000ns max) Interrupt: pin A routed to IRQ 19 Region 0: I/O ports at c400 [size=64] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 USB Controller: VIA Technologies, Inc. UHCI USB (rev 80) (prog-if 00 [UHCI]) Subsystem: ABIT Computer Corp.: Unknown device 1401 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin A routed to IRQ 0 Region 4: I/O ports at c800 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.1 USB Controller: VIA Technologies, Inc. UHCI USB (rev 80) (prog-if 00 [UHCI]) Subsystem: ABIT Computer Corp.: Unknown device 1401 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin B routed to IRQ 0 Region 4: I/O ports at cc00 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 80) (prog-if 00 [UHCI]) Subsystem: ABIT Computer Corp.: Unknown device 1401 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin C routed to IRQ 0 Region 4: I/O ports at d000 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.3 USB Controller: VIA Technologies, Inc.: Unknown device 3104 (rev 82) (prog-if 20) Subsystem: ABIT Computer Corp.: Unknown device 1401 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin D routed to IRQ 0 Region 0: Memory at e6023000 (32-bit, non-prefetchable) [size=256] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.0 ISA bridge: VIA Technologies, Inc.: Unknown device 3177 Subsystem: VIA Technologies, Inc.: Unknown device 3177 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: VIA Technologies, Inc. Bus Master IDE Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Interrupt: pin A routed to IRQ 11 Region 4: I/O ports at d400 [size=16] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:13.0 RAID bus controller: Triones Technologies, Inc. HPT366 / HPT370 (rev 05) Subsystem: Triones Technologies, Inc.: Unknown device 0001 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (2000ns min, 2000ns max), cache line size 08 Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at d800 [size=8] Region 1: I/O ports at dc00 [size=4] Region 2: I/O ports at e000 [size=8] Region 3: I/O ports at e400 [size=4] Region 4: I/O ports at e800 [size=256] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: nVidia Corporation: Unknown device 0171 (rev a3) (prog-if 00 [VGA]) Subsystem: ABIT Computer Corp.: Unknown device 8f00 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 248 (1250ns min, 250ns max) Interrupt: pin A routed to IRQ 16 Region 0: Memory at e4000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at d0000000 (32-bit, prefetchable) [size=128M] Region 2: Memory at d8000000 (32-bit, prefetchable) [size=512K] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [44] AGP version 2.0 Status: RQ=31 SBA- 64bit- FW+ Rate=x1,x2 Command: RQ=31 SBA- AGP+ 64bit- FW- Rate=<none>
[7.6.] Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: ASUS Model: CRW-1610A Rev: 1.10 Type: CD-ROM ANSI SCSI revision: 02 Host: scsi0 Channel: 00 Id: 01 Lun: 00 Vendor: PIONEER Model: DVD-ROM DVD-106 Rev: 1.22 Type: CD-ROM ANSI SCSI revision: 02 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: Maxtor 4 Model: G120J6 Rev: GAK8 Type: Direct-Access ANSI SCSI revision: 02
[7.7.] None.
Erno Rigo - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |