Messages in this thread | | | Date | Thu, 13 Feb 2003 12:26:13 -0600 | From | Daniel Nash <> | Subject | Two IDE controller cards dropping DMA mode |
| |
I am having trouble setting up a server with two Silicon Image CMD680 cards (Siig UltraATA 133 PCI). I have one WD2000JB 200GB hard disk on each of four channels (two per card). When I start hitting both cards hard by starting RAID 5 on the drives, two of the four channels have errors and drop DMA mode. After this, the machine of course performs poorly.
Example:
hdg: dma_intr: status=0x7f { DriveReady DeviceFault SeekComplete DataRequest CorrectedError Index Error } hdg: dma_intr: error=0x00 { } hdg: DMA disabled ide3: reset: success
This also happens with hda. Swapping things around doesn't change the problem. If I reset the channel to use UDMA(100) again, the problem recurs.
I've tried this with 2.4.20 and 2.4.21-pre4-ac4. I would try 2.5.x, but 59 and 60 and various BK snaps won't boot on my machine.
I've also tried two PDC20269 (Promise Ultra133 TX2) cards in the same setup, but those would hang the machine when both were in use at once, no oops, no error messages.
I've tried the kernel config more minimal, with and without APIC and ACPI and Power Management, and without extras, and there was no difference. I've tried everything compiled in instead of using some modules. My current config is at the end of this message.
This is an Athlon 1.46 GHz with an ASUS A7V333 (VIA KT333 chipset) motherboard. I'm running Debian testing.
Any ideas?
Please CC replies to me.
Thanks for any help, - Daniel Nash
ver_info: Linux slic 2.4.21-pre4-ac4 #7 Tue Feb 11 10:12:32 CST 2003 i686 AMD Athlon(TM) XP 1700+ AuthenticAMD GNU/Linux Gnu C 2.95.4 Gnu make 3.79.1 util-linux 2.11n mount 2.11n modutils 2.4.19 e2fsprogs 1.30-WIP pcmcia-cs 3.1.33 Linux C Library 2.2.5 Dynamic linker (ldd) 2.2.5 Procps 2.0.7 Net-tools 1.60 Console-tools 0.2.3 Sh-utils 4.5.2 Modules Loaded raid5 xor appletalk md
lspci -vvv:
00:00.0 Host bridge: VIA Technologies, Inc. VT8367 [KT266] Subsystem: Asustek Computer, Inc.: Unknown device 807f Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort+ <MAbort+ >SERR- <PERR- Latency: 0 Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M] Capabilities: [a0] AGP version 2.0 Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2,x4 Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none> Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8367 [KT266 AGP] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000e000-0000dfff Memory behind bridge: dc000000-ddcfffff Prefetchable memory behind bridge: ddf00000-dfffffff BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:05.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10) Subsystem: Asustek Computer, Inc.: Unknown device 80e2 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (500ns min, 6000ns max) Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at d800 [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 USB Controller: VIA Technologies, Inc. USB (rev 50) (prog-if 00 [UHCI]) Subsystem: Asustek Computer, Inc.: Unknown device 8080 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin A routed to IRQ 3 Region 4: I/O ports at d400 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.1 USB Controller: VIA Technologies, Inc. USB (rev 50) (prog-if 00 [UHCI]) Subsystem: Asustek Computer, Inc.: Unknown device 8080 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin B routed to IRQ 11 Region 4: I/O ports at d000 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 51) (prog-if 20 [EHCI]) Subsystem: Asustek Computer, Inc.: Unknown device 8080 Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin C routed to IRQ 10 Region 0: Memory at db800000 (32-bit, non-prefetchable) [disabled] [size=256] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 Unknown mass storage controller: CMD Technology Inc PCI0680 (rev 02) Subsystem: CMD Technology Inc PCI0680 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 01 Interrupt: pin A routed to IRQ 3 Region 0: I/O ports at b800 [size=8] Region 1: I/O ports at b400 [size=4] Region 2: I/O ports at b000 [size=8] Region 3: I/O ports at a800 [size=4] Region 4: I/O ports at a400 [size=16] Region 5: Memory at db000000 (32-bit, non-prefetchable) [size=256] Expansion ROM at <unassigned> [disabled] [size=512K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:0e.0 Unknown mass storage controller: CMD Technology Inc PCI0680 (rev 02) Subsystem: CMD Technology Inc PCI0680 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort+ <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 01 Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at a000 [size=8] Region 1: I/O ports at 9800 [size=4] Region 2: I/O ports at 9400 [size=8] Region 3: I/O ports at 9000 [size=4] Region 4: I/O ports at 8800 [size=16] Region 5: Memory at da800000 (32-bit, non-prefetchable) [size=256] Expansion ROM at <unassigned> [disabled] [size=512K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:0f.0 Ethernet controller: Linksys Network Everywhere Fast Ethernet 10/100 model NC100 (rev 11) Subsystem: Linksys: Unknown device 0574 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (16000ns min, 32000ns max), cache line size 08 Interrupt: pin A routed to IRQ 5 Region 0: I/O ports at 8400 [size=256] Region 1: Memory at da000000 (32-bit, non-prefetchable) [size=1K] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=100mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.0 ISA bridge: VIA Technologies, Inc. VT8233A ISA Bridge Subsystem: Asustek Computer, Inc.: Unknown device 808c Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: Asustek Computer, Inc.: Unknown device 808c Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Interrupt: pin A routed to IRQ 0 Region 4: I/O ports at 8000 [size=16] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.2 USB Controller: VIA Technologies, Inc. USB (rev 23) (prog-if 00 [UHCI]) Subsystem: Asustek Computer, Inc.: Unknown device 808c Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin D routed to IRQ 7 Region 4: I/O ports at 7800 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.3 USB Controller: VIA Technologies, Inc. USB (rev 23) (prog-if 00 [UHCI]) Subsystem: Asustek Computer, Inc.: Unknown device 808c Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin D routed to IRQ 7 Region 4: I/O ports at 7400 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: nVidia Corporation NV6 [Vanta] (rev 15) (prog-if 00 [VGA]) Subsystem: Micro-star International Co Ltd MSI-8808 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (1250ns min, 250ns max) Interrupt: pin A routed to IRQ 11 Region 0: Memory at dc000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at de000000 (32-bit, prefetchable) [size=32M] Expansion ROM at ddff0000 [disabled] [size=64K] Capabilities: [60] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [44] AGP version 2.0 Status: RQ=31 SBA- 64bit- FW- Rate=x1,x2,x4 Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
dmesg: hdg: dma_intr: status=0x7f { DriveReady DeviceFault SeekComplete DataRequest CorrectedError Index Error } hdg: dma_intr: error=0x00 { } hdg: DMA disabled ide3: reset: success hdg: read_intr: status=0x7f { DriveReady DeviceFault SeekComplete DataRequest CorrectedError Index Error } hdg: read_intr: error=0x00 { } ide3: reset: success hdg: read_intr: status=0x7f { DriveReady DeviceFault SeekComplete DataRequest CorrectedError Index Error } hdg: read_intr: error=0x00 { } ide3: reset: success hdg: dma_intr: status=0x58 { DriveReady SeekComplete DataRequest }
hdg: CHECK for good STATUS hda: dma_intr: status=0x7f { DriveReady DeviceFault SeekComplete DataRequest CorrectedError Index Error } hda: dma_intr: error=0x00 { } hda: DMA disabled ide0: reset: success hda: read_intr: status=0x7f { DriveReady DeviceFault SeekComplete DataRequest CorrectedError Index Error } hda: read_intr: error=0x00 { } ide0: reset: success hda: read_intr: status=0x7f { DriveReady DeviceFault SeekComplete DataRequest CorrectedError Index Error } hda: read_intr: error=0x00 { } ide0: reset: success hda: read_intr: status=0x7f { DriveReady DeviceFault SeekComplete DataRequest CorrectedError Index Error } hda: read_intr: error=0x00 { } ide0: reset: success hda: read_intr: status=0x7f { DriveReady DeviceFault SeekComplete DataRequest CorrectedError Index Error } hda: read_intr: error=0x00 { } hdg: dma_intr: status=0x7f { DriveReady DeviceFault SeekComplete DataRequest CorrectedError Index Error } hdg: dma_intr: error=0x00 { } hdg: DMA disabled ide0: reset: success ide3: reset: success
config: CONFIG_X86=y CONFIG_UID16=y CONFIG_EXPERIMENTAL=y CONFIG_MODULES=y CONFIG_MODVERSIONS=y CONFIG_KMOD=y CONFIG_MK7=y CONFIG_X86_WP_WORKS_OK=y CONFIG_X86_INVLPG=y CONFIG_X86_CMPXCHG=y CONFIG_X86_XADD=y CONFIG_X86_BSWAP=y CONFIG_X86_POPAD_OK=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_X86_L1_CACHE_SHIFT=6 CONFIG_X86_HAS_TSC=y CONFIG_X86_GOOD_APIC=y CONFIG_X86_USE_3DNOW=y CONFIG_X86_PGE=y CONFIG_X86_USE_PPRO_CHECKSUM=y CONFIG_X86_F00F_WORKS_OK=y CONFIG_X86_MCE=y CONFIG_X86_CPUID=m CONFIG_NOHIGHMEM=y CONFIG_X86_UP_APIC=y CONFIG_X86_UP_IOAPIC=y CONFIG_X86_LOCAL_APIC=y CONFIG_X86_IO_APIC=y CONFIG_X86_TSC=y CONFIG_NET=y CONFIG_PCI=y CONFIG_PCI_GOANY=y CONFIG_PCI_BIOS=y CONFIG_PCI_DIRECT=y CONFIG_PCI_NAMES=y CONFIG_SYSVIPC=y CONFIG_BSD_PROCESS_ACCT=y CONFIG_SYSCTL=y CONFIG_KCORE_ELF=y CONFIG_BINFMT_AOUT=y CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=y CONFIG_IKCONFIG=y CONFIG_PM=y CONFIG_PNP=y CONFIG_BLK_DEV_FD=m CONFIG_BLK_DEV_LOOP=m CONFIG_BLK_DEV_RAM=m CONFIG_BLK_DEV_RAM_SIZE=4096 CONFIG_BLK_STATS=y CONFIG_MD=y CONFIG_BLK_DEV_MD=m CONFIG_MD_LINEAR=m CONFIG_MD_RAID0=m CONFIG_MD_RAID1=m CONFIG_MD_RAID5=m CONFIG_MD_MULTIPATH=m CONFIG_PACKET=y CONFIG_UNIX=y CONFIG_INET=y CONFIG_IP_MULTICAST=y CONFIG_ATALK=m CONFIG_IDE=y CONFIG_BLK_DEV_IDE=y CONFIG_BLK_DEV_IDEDISK=y CONFIG_IDEDISK_MULTI_MODE=y CONFIG_BLK_DEV_IDECD=m CONFIG_BLK_DEV_CMD640=y CONFIG_BLK_DEV_IDEPCI=y CONFIG_IDEPCI_SHARE_IRQ=y CONFIG_BLK_DEV_IDEDMA_PCI=y CONFIG_IDEDMA_PCI_AUTO=y CONFIG_BLK_DEV_IDEDMA=y CONFIG_BLK_DEV_ADMA=y CONFIG_BLK_DEV_CMD64X=y CONFIG_BLK_DEV_PDC202XX_OLD=y CONFIG_BLK_DEV_PDC202XX_NEW=y CONFIG_BLK_DEV_RZ1000=y CONFIG_BLK_DEV_SIIMAGE=y CONFIG_BLK_DEV_VIA82CXXX=y CONFIG_IDEDMA_AUTO=y CONFIG_BLK_DEV_PDC202XX=y CONFIG_BLK_DEV_IDE_MODES=y CONFIG_SCSI=m CONFIG_BLK_DEV_SD=m CONFIG_SD_EXTRA_DEVS=40 CONFIG_SCSI_DEBUG_QUEUES=y CONFIG_SCSI_MULTI_LUN=y CONFIG_SCSI_CONSTANTS=y CONFIG_SCSI_SYM53C8XX=m CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS=4 CONFIG_SCSI_NCR53C8XX_MAX_TAGS=32 CONFIG_SCSI_NCR53C8XX_SYNC=20 CONFIG_NETDEVICES=y CONFIG_DUMMY=m CONFIG_NET_ETHERNET=y CONFIG_NET_PCI=y CONFIG_TULIP=y CONFIG_VT=y CONFIG_VT_CONSOLE=y CONFIG_SERIAL=y CONFIG_UNIX98_PTYS=y CONFIG_UNIX98_PTY_COUNT=256 CONFIG_MOUSE=y CONFIG_PSMOUSE=y CONFIG_AUTOFS4_FS=y CONFIG_REISERFS_FS=m CONFIG_HFS_FS=m CONFIG_EXT3_FS=y CONFIG_JBD=y CONFIG_TMPFS=y CONFIG_RAMFS=y CONFIG_ISO9660_FS=y CONFIG_JOLIET=y CONFIG_PROC_FS=y CONFIG_DEVPTS_FS=y CONFIG_EXT2_FS=y CONFIG_UDF_FS=m CONFIG_NFS_FS=m CONFIG_NFS_V3=y CONFIG_NFSD=m CONFIG_NFSD_V3=y CONFIG_SUNRPC=m CONFIG_LOCKD=m CONFIG_LOCKD_V4=y CONFIG_SMB_FS=m CONFIG_MSDOS_PARTITION=y CONFIG_SMB_NLS=y CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_VGA_CONSOLE=y CONFIG_VIDEO_SELECT=y CONFIG_SOUND=y CONFIG_SOUND_CMPCI=y CONFIG_USB=y CONFIG_USB_UHCI_ALT=y CONFIG_USB_STORAGE=m
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |