Messages in this thread | | | Date | Thu, 04 Dec 2003 10:20:31 +0100 | From | Martin Lorenz <> | Subject | PROBLEM: 2.6.0-test[9|10] freeze after resume (ACPI) |
| |
please CC as i am not subscribed to lkml
I would also like to contribute a solution to the problem, as soon as someone tells me where i should start searching... i am a quite experienced programmer, but have not yet looked into the kernel, so it's a bit like tapping blindfolded in a maze when i start doing so.
in short: On my SHARP PC-MM10 suspend to disk/ram works nicely until back from resume. At that moment it completely freezes.
I already tried several variants of kernel konfiguration, unloaded all modules, stopped all daemons and switched to single user mode to have barely more than the kernel, init and a shell running.
when suspending to ram or disk (echo -n [mem|disk] > /sys/power/state or echo [3|4] > /proc/acpi/sleep) it goes down nicely with only an annoying backlight on and white screen in mem mode - which i currently ignore because the backlight is switched off anyway when closing the lid.
after resume it comes back to the very screen i left off (no matter if X or console) but does not react on any key nor mouse action anymore.
here comes the system description: ------------------------- # cat /proc/version Linux version 2.6.0-test10 (mlo@mellon) (gcc version 3.3.2 (Debian)) #1 Tue Nov 25 20:48:42 CET 2003
----------------------- # sh scripts/ver_linux If some fields are empty or look unusual you may have an old version. Compare to the current minimal requirements in Documentation/Changes.
Linux mellon 2.6.0-test10 #1 Tue Nov 25 20:48:42 CET 2003 i686 GNU/Linux
Gnu C 3.3.2 Gnu make 3.80 util-linux 2.12 mount 2.11x module-init-tools 0.9.15-pre3 e2fsprogs 1.35-WIP jfsutils 1.1.4 xfsprogs 2.6.0 pcmcia-cs 3.2.5 PPP 2.4.2b3 nfs-utils 1.0.6 Linux C Library 2.3.2 Dynamic linker (ldd) 2.3.2 Procps 3.1.14 Net-tools 1.60 Console-tools 0.2.3 Sh-utils 5.0.91 Modules Loaded ds yenta_socket pcmcia_core evdev orinoco_pci orinoco hermes ohci_hcd usbcore 8139too mii crc32 msr cpuid rtc
------------------------- # cat /proc/cpuinfo processor : 0 vendor_id : GenuineTMx86 cpu family : 6 model : 4 model name : Transmeta(tm) Crusoe(tm) Processor TM5800 stepping : 3 cpu MHz : 993.057 cache size : 512 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 1 wp : yes flags : fpu vme de tsc msr cx8 sep cmov mmx longrun lrti bogomips : 1949.69
--------------------------- # cat /proc/modules ds 11492 2 - Live 0xcf8a2000 yenta_socket 16736 0 - Live 0xcf898000 pcmcia_core 59776 2 ds,yenta_socket, Live 0xcf888000 evdev 8320 1 - Live 0xcf8b1000 orinoco_pci 6400 0 - Live 0xcf868000 orinoco 60268 1 orinoco_pci, Live 0xcf86f000 hermes 9120 2 orinoco_pci,orinoco, Live 0xcf864000 ohci_hcd 37472 0 - Live 0xcf857000 usbcore 130074 1 - Loading 0xcfa29000 8139too 28320 0 - Live 0xcf84b000 mii 4224 1 8139too, Live 0xcf848000 crc32 4000 1 8139too, Live 0xcf862000 msr 3104 0 - Live 0xcf86d000 cpuid 2784 0 - Live 0xcf86b000 rtc 20636 0 - Live 0xcf87f000
-------------------------- # cat /proc/iomem 00000000-0009abff : System RAM 0009ac00-0009ffff : reserved 000a0000-000bffff : Video RAM area 000cc000-000ccfff : Extension ROM 000da000-000dafff : 0000:00:0c.0 000da000-000dafff : ohci_hcd 000db000-000dbfff : 0000:00:0c.1 000db000-000dbfff : ohci_hcd 000dc000-000dffff : reserved 000f0000-000fffff : System ROM 00100000-0e6effff : System RAM 00100000-003b6ce8 : Kernel code 003b6ce9-0049853f : Kernel data 0e6f0000-0e6fefff : ACPI Tables 0e6ff000-0e6fffff : ACPI Non-volatile Storage 0e700000-0e7fffff : System RAM 10000000-10000fff : 0000:00:05.0 10000000-10000fff : yenta_socket 10400000-107fffff : PCI CardBus #01 10800000-10bfffff : PCI CardBus #01 f4000000-f40fffff : 0000:00:00.0 f4100000-f4100fff : 0000:00:06.0 f4101000-f41010ff : 0000:00:0a.0 f4101000-f41010ff : 8139too f4101400-f41014ff : 0000:00:0c.2 f4104000-f4104fff : 0000:00:0b.0 f8000000-fbffffff : 0000:00:09.0 f8200000-f89fffff : vesafb fff80000-ffffffff : reserved
--------------------- # cat /proc/ioports 0000-001f : dma1 0020-0021 : pic1 0040-005f : timer 0060-006f : keyboard 0070-0077 : rtc 0080-008f : dma page reg 00a0-00a1 : pic2 00c0-00df : dma2 00f0-00ff : fpu 01f0-01f7 : ide0 0398-0399 : pnp 00:02 03c0-03df : vesafb 03f6-03f6 : ide0 040b-040b : pnp 00:02 04d0-04d1 : pnp 00:0a 0cf8-0cff : PCI conf1 1000-100f : 0000:00:10.0 1000-1007 : ide0 1008-100f : ide1 1400-14ff : 0000:00:06.0 1800-18ff : 0000:00:0a.0 1800-18ff : 8139too 4000-40ff : PCI CardBus #01 4400-44ff : PCI CardBus #01 8000-803f : 0000:00:11.0 8000-803f : pnp 00:0a 8040-805f : 0000:00:11.0 8040-804f : pnp 00:0a
----------------------- # cat /proc/interrupts CPU0 0: 2092157 XT-PIC timer 1: 5602 XT-PIC i8042 2: 0 XT-PIC cascade 3: 1134 XT-PIC eth0 4: 0 XT-PIC eth1 5: 0 XT-PIC ohci_hcd, ohci_hcd 8: 4 XT-PIC rtc 9: 0 XT-PIC acpi 10: 0 XT-PIC yenta 12: 178420 XT-PIC i8042 14: 5086 XT-PIC ide0 NMI: 0 LOC: 0 ERR: 0 MIS: 0 -------------------- # cat /proc/acpi/sleep S0 S3 S4 S5 00:00.0 Host bridge: Transmeta Corporation LongRun Northbridge (rev 03) Subsystem: Sharp corporation: Unknown device 102b Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 64 Region 0: Memory at f4000000 (32-bit, non-prefetchable) [size=1M]
00:00.1 RAM memory: Transmeta Corporation SDRAM controller Subsystem: Sharp corporation: Unknown device 102b Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:00.2 RAM memory: Transmeta Corporation BIOS scratchpad Subsystem: Sharp corporation: Unknown device 102b Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:05.0 CardBus bridge: Ricoh Co Ltd RL5c475 (rev 81) Subsystem: Sharp corporation: Unknown device 102b Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168 Interrupt: pin A routed to IRQ 10 Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=01, subordinate=04, sec-latency=176 Memory window 0: 10400000-107ff000 (prefetchable) Memory window 1: 10800000-10bff000 I/O window 0: 00004000-000040ff I/O window 1: 00004400-000044ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001
00:06.0 Multimedia audio controller: ALi Corporation M5451 PCI AC-Link Controller Audio Device (rev 02) Subsystem: Sharp corporation: Unknown device 102b Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR+ <PERR+ Latency: 64 (500ns min, 6000ns max) Interrupt: pin A routed to IRQ 9 Region 0: I/O ports at 1400 [size=256] Region 1: Memory at f4100000 (32-bit, non-prefetchable) [size=4K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: ALi Corporation M1533 PCI to ISA Bridge [Aladdin IV] Subsystem: Sharp corporation: Unknown device 102b Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [a0] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 VGA compatible controller: Silicon Motion, Inc. SM720 Lynx3DM (rev c1) (prog-if 00 [VGA]) Subsystem: Sharp corporation: Unknown device 102b Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Interrupt: pin A routed to IRQ 7 Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=64M] Capabilities: [40] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] AGP version 2.0 Status: RQ=1 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=<none> Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Sharp corporation: Unknown device 102b Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (8000ns min, 16000ns max) Interrupt: pin A routed to IRQ 3 Region 0: I/O ports at 1800 [size=256] Region 1: Memory at f4101000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.0 Network controller: Harris Semiconductor Prism 2.5 Wavelan chipset (rev 01) Subsystem: AMBIT Microsystem Corp.: Unknown device 0200 Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 4 Region 0: Memory at f4104000 (32-bit, prefetchable) [size=4K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI]) Subsystem: Sharp corporation: Unknown device 102b Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (250ns min, 10500ns max), Cache Line Size: 0x08 (32 bytes) Interrupt: pin A routed to IRQ 5 Region 0: Memory at 000da000 (32-bit, non-prefetchable) [size=4K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.1 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI]) Subsystem: Sharp corporation: Unknown device 102b Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (250ns min, 10500ns max), Cache Line Size: 0x08 (32 bytes) Interrupt: pin B routed to IRQ 5 Region 0: Memory at 000db000 (32-bit, non-prefetchable) [size=4K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.2 USB Controller: NEC Corporation USB 2.0 (rev 02) (prog-if 20 [EHCI]) Subsystem: Sharp corporation: Unknown device 102b Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 132 (4000ns min, 8500ns max), Cache Line Size: 0x08 (32 bytes) Interrupt: pin C routed to IRQ 11 Region 0: Memory at f4101400 (32-bit, non-prefetchable) [disabled] [size=256] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 IDE interface: ALi Corporation M5229 IDE (rev c4) (prog-if ea) Subsystem: Sharp corporation: Unknown device 102b Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (500ns min, 1000ns max) Interrupt: pin A routed to IRQ 255 Region 4: I/O ports at 1000 [size=16] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.0 Bridge: ALi Corporation M7101 PMU Subsystem: Sharp corporation: Unknown device 102b Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Linux version 2.6.0-test10 (mlo@mellon) (gcc version 3.3.2 (Debian)) #1 Tue Nov 25 20:48:42 CET 2003 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009ac00 (usable) BIOS-e820: 000000000009ac00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000dc000 - 00000000000e0000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000000e6f0000 (usable) BIOS-e820: 000000000e6f0000 - 000000000e6ff000 (ACPI data) BIOS-e820: 000000000e6ff000 - 000000000e700000 (ACPI NVS) BIOS-e820: 000000000e700000 - 000000000e800000 (usable) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 232MB LOWMEM available. On node 0 totalpages: 59392 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 55296 pages, LIFO batch:13 HighMem zone: 0 pages, LIFO batch:1 DMI present. ACPI: RSDP (v000 PTLTD ) @ 0x000f7420 ACPI: RSDT (v001 PTLTD RSDT 0x06040005 LTP 0x00000000) @ 0x0e6fbdfb ACPI: FADT (v001 TMETA RSDT 0x06040005 PTL 0x000f4240) @ 0x0e6fef8c ACPI: DSDT (v001 PTLTD DSDT 0x06040005 MSFT 0x0100000e) @ 0x00000000 Building zonelist for node : 0 Kernel command line: BOOT_IMAGE=test10nr ro root=303 noresume No local APIC present or hardware disabled Initializing CPU#0 PID hash table entries: 1024 (order 10: 8192 bytes) Detected 993.057 MHz processor. Console: colour dummy device 80x25 Memory: 230088k/237568k available (2779k kernel code, 6704k reserved, 902k data, 172k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 1949.69 BogoMIPS Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: 0080893f 0081813f 00000000 00000000 CPU: After vendor identify, caps: 0080893f 0081813f 000000ce 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (32 bytes/line) CPU: L2 Cache: 512K (128 bytes/line) CPU: Processor revision 1.5.0.2, 1000 MHz CPU: Code Morphing Software revision 4.3.4-9-540 CPU: 20021104 07:53 official release 4.3.4#1 CPU: After all inits, caps: 00808937 0081813f 000000ce 00000000 CPU: Transmeta(tm) Crusoe(tm) Processor TM5800 stepping 03 Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfd8ae, last bus=0 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20031002 tbxface-0117 [03] acpi_load_tables : ACPI Tables successfully acquired Parsing all Control Methods:............................................................................................................ Table [DSDT](id F004) - 397 Objects with 40 Devices 108 Methods 17 Regions ACPI Namespace successfully loaded at root c04e61fc evxfevnt-0093 [04] acpi_enable : Transition to ACPI mode successful evgpeblk-0748 [06] ev_create_gpe_block : GPE 00 to 63 [_GPE] 8 regs at 0000000000008018 on int 9 Completing Region/Field/Buffer/Package initialization:....................................................... Initialized 17/17 Regions 0/0 Fields 12/12 Buffers 26/26 Packages (405 nodes) Executing all Device _STA and_INI methods:......................................... 41 Devices found containing: 41 _STA, 2 _INI methods ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNK1] (IRQs *7) ACPI: PCI Interrupt Link [LNK2] (IRQs 10) ACPI: PCI Interrupt Link [LNK3] (IRQs *5) ACPI: PCI Interrupt Link [LNK4] (IRQs *11) ACPI: PCI Interrupt Link [LNK5] (IRQs *3) ACPI: PCI Interrupt Link [LNK6] (IRQs *4) ACPI: PCI Interrupt Link [LNKM] (IRQs 3 4 5 7 9 10 11) ACPI: PCI Interrupt Link [LNKA] (IRQs *9) ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 7 9 10 11) Linux Plug and Play Support v0.97 (c) Adam Belay PnPBIOS: Scanning system for PnP BIOS support... PnPBIOS: Found PnP BIOS installation structure at 0xc00f74a0 PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x8a77, dseg 0x400 pnp: 00:02: ioport range 0x398-0x399 has been reserved pnp: 00:02: ioport range 0x40b-0x40b has been reserved pnp: 00:0a: ioport range 0x4d0-0x4d1 has been reserved pnp: 00:0a: ioport range 0x8000-0x803f has been reserved pnp: 00:0a: ioport range 0x8040-0x804f has been reserved PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver SCSI subsystem initialized drivers/usb/core/usb.c: registered new driver usbfs drivers/usb/core/usb.c: registered new driver hub ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 10 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9 ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 7 ACPI: PCI Interrupt Link [LNK5] enabled at IRQ 3 ACPI: PCI Interrupt Link [LNK6] enabled at IRQ 4 ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 5 ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 11 pci_irq-0302 [33] acpi_pci_irq_derive : Unable to derive IRQ for device 0000:00:10.0 ACPI: No IRQ known for interrupt pin A of device 0000:00:10.0 - using IRQ 255 PCI: Using ACPI for IRQ routing PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off' vesafb: framebuffer at 0xf8200000, mapped to 0xcf009000, size 8192k vesafb: mode is 1024x768x16, linelength=2048, pages=4 vesafb: protected mode interface info at ca87:0002 vesafb: scrolling: redraw vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0 fb0: VESA VGA frame buffer device ikconfig 0.7 with /proc/config* Installing knfsd (copyright (C) 1996 okir@monad.swb.de). udf: registering filesystem Initializing Cryptographic API ACPI: AC Adapter [ADP1] (on-line) ACPI: Battery Slot [BAT0] (battery present) ACPI: Power Button (FF) [PWRF] ACPI: Lid Switch [LID] ACPI: Processor [CPU0] (supports C1) ACPI: Thermal Zone [THRM] (41 C) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Console: switching to colour frame buffer device 128x48 pty: 256 Unix98 ptys configured Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ALI15X3: IDE controller at PCI slot 0000:00:10.0 pci_irq-0302 [32] acpi_pci_irq_derive : Unable to derive IRQ for device 0000:00:10.0 ACPI: No IRQ known for interrupt pin A of device 0000:00:10.0 - using IRQ 255 ALI15X3: chipset revision 196 ALI15X3: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x1000-0x1007, BIOS settings: hda:DMA, hdb:pio ALI15X3: simplex device: DMA forced ide1: BM-DMA at 0x1008-0x100f, BIOS settings: hdc:DMA, hdd:DMA hda: TOSHIBA MK1503GAL, ATA DISK drive Using anticipatory io scheduler ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: max request size: 128KiB hda: 29297520 sectors (15000 MB), CHS=29065/16/63, UDMA(100) hda: hda1 hda2 < hda5 hda6 hda7 hda8 > hda3 Console: switching to colour frame buffer device 128x48 mice: PS/2 mouse device common for all mice i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 Synaptics Touchpad, model: 1 Firmware: 5.9 180 degree mounted touchpad Sensor: 34 new absolute packet format Touchpad has extended capability bits -> multifinger detection -> palm detection input: SynPS/2 Synaptics TouchPad on isa0060/serio4 serio: i8042 AUX3 port at 0x60,0x64 irq 12 input: AT Translated Set 2 keyboard on isa0060/serio0 serio: i8042 KBD port at 0x60,0x64 irq 1 NET: Registered protocol family 2 IP: routing cache hash table of 512 buckets, 16Kbytes TCP: Hash tables configured (established 16384 bind 4681) NET: Registered protocol family 1 NET: Registered protocol family 17 cpufreq: No CPUs supporting ACPI performance management found. PM: Reading pmdisk image. PM: Resume from disk failed. ACPI: (supports S0 S3 S4 S5) VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 172k freed Adding 497972k swap on /dev/hda8. Priority:-1 extents:1 Real Time Clock Driver v1.12 warning: process `update' used the obsolete bdflush system call Fix your initscripts? 8139too Fast Ethernet driver 0.9.26 eth0: RealTek RTL8139 at 0xcf855000, 08:00:1f:b1:7c:5e, IRQ 3 eth0: Identified 8139 chip type 'RTL-8100B/8139D' Unable to handle kernel NULL pointer dereference at virtual address 00000020 printing eip: c01d0227 *pde = 00000000 Oops: 0000 [#1] CPU: 0 EIP: 0060:[<c01d0227>] Not tainted EFLAGS: 00010282 EIP is at create_dir+0x17/0xc0 eax: 00000077 ebx: cfa47bc8 ecx: 00000000 edx: cfa47bcc esi: cfa47bc8 edi: 00000000 ebp: cd8a7f0c esp: cd8a7ef4 ds: 007b es: 007b ss: 0068 Process modprobe (pid: 57, threadinfo=cd8a6000 task=cd8cd960) Stack: cfa47b14 cfa47b14 00000246 cfa47bc8 cfa47bc8 cfa47bc8 cd8a7f2c c01d033f cfa47bc8 00000000 cfa47bcc cd8a7f24 00000000 00000000 cd8a7f40 c024642f cfa47bc8 cfa47b00 cfa47b04 cd8a7f64 c0246a11 cfa47bc8 cfa47bc8 cfa47bb8 Call Trace: [<c01d033f>] sysfs_create_dir+0x3f/0x80 [<c024642f>] create_dir+0x1f/0x50 [<c0246a11>] kobject_add+0x51/0x150 [<c02b99ed>] bus_register+0x5d/0xa0 [<cf85303c>] usb_init+0x3c/0x60 [usbcore] [<c014d914>] sys_init_module+0x1f4/0x3d0 [<c010b1cb>] syscall_call+0x7/0xb
Code: 8b 77 20 89 44 24 04 c7 04 24 0c e9 3c c0 8d 9e 80 00 00 00 <7>ohci_hcd: 2003 Oct 13 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ohci_hcd: block sizes: ed 64 td 64 ohci_hcd 0000:00:0c.0: OHCI Host Controller ohci_hcd 0000:00:0c.0: reset, control = 0xc3 ohci_hcd 0000:00:0c.0: irq 5, pci mem c00da000 ohci_hcd 0000:00:0c.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:0c.0: root hub device address 1 usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 drivers/usb/core/message.c: USB device number 1 default language ID 0x409 usb usb1: Product: OHCI Host Controller usb usb1: Manufacturer: Linux 2.6.0-test10 ohci_hcd usb usb1: SerialNumber: 0000:00:0c.0 drivers/usb/core/usb.c: usb_hotplug usb usb1: registering 1-0:1.0 (config #1, interface 0) drivers/usb/core/usb.c: usb_hotplug hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected hub 1-0:1.0: standalone hub hub 1-0:1.0: ganged power switching hub 1-0:1.0: global over-current protection hub 1-0:1.0: Port indicators are not supported hub 1-0:1.0: power on to power good time: 2ms hub 1-0:1.0: hub controller current requirement: 0mA hub 1-0:1.0: local power source is good hub 1-0:1.0: no over-current condition exists hub 1-0:1.0: enabling power on all ports ohci_hcd 0000:00:0c.0: created debug files ohci_hcd 0000:00:0c.0: OHCI controller state ohci_hcd 0000:00:0c.0: OHCI 1.0, with legacy support registers ohci_hcd 0000:00:0c.0: control 0x08f HCFS=operational IE PLE CBSR=3 ohci_hcd 0000:00:0c.0: cmdstatus 0x00000 SOC=0 ohci_hcd 0000:00:0c.0: intrstatus 0x00000004 SF ohci_hcd 0000:00:0c.0: intrenable 0x80000012 MIE UE WDH ohci_hcd 0000:00:0c.0: hcca frame #0575 ohci_hcd 0000:00:0c.0: roothub.a 01000201 POTPGT=1 NPS NDP=1 ohci_hcd 0000:00:0c.0: roothub.b 00000000 PPCM=0000 DR=0000 ohci_hcd 0000:00:0c.0: roothub.status 00000000 ohci_hcd 0000:00:0c.0: roothub.portstatus [0] 0x00000100 PPS ohci_hcd 0000:00:0c.1: OHCI Host Controller ohci_hcd 0000:00:0c.1: reset, control = 0xc3 ohci_hcd 0000:00:0c.1: irq 5, pci mem c00db000 ohci_hcd 0000:00:0c.1: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:0c.1: root hub device address 1 usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 drivers/usb/core/message.c: USB device number 1 default language ID 0x409 usb usb2: Product: OHCI Host Controller usb usb2: Manufacturer: Linux 2.6.0-test10 ohci_hcd usb usb2: SerialNumber: 0000:00:0c.1 drivers/usb/core/usb.c: usb_hotplug usb usb2: registering 2-0:1.0 (config #1, interface 0) drivers/usb/core/usb.c: usb_hotplug hub 2-0:1.0: usb_probe_interface hub 2-0:1.0: usb_probe_interface - got id hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected hub 2-0:1.0: standalone hub hub 2-0:1.0: ganged power switching hub 2-0:1.0: global over-current protection hub 2-0:1.0: Port indicators are not supported hub 2-0:1.0: power on to power good time: 2ms hub 2-0:1.0: hub controller current requirement: 0mA hub 2-0:1.0: local power source is good hub 2-0:1.0: no over-current condition exists hub 2-0:1.0: enabling power on all ports ohci_hcd 0000:00:0c.1: created debug files ohci_hcd 0000:00:0c.1: OHCI controller state ohci_hcd 0000:00:0c.1: OHCI 1.0, with legacy support registers ohci_hcd 0000:00:0c.1: control 0x08f HCFS=operational IE PLE CBSR=3 ohci_hcd 0000:00:0c.1: cmdstatus 0x00000 SOC=0 ohci_hcd 0000:00:0c.1: intrstatus 0x00000004 SF ohci_hcd 0000:00:0c.1: intrenable 0x80000012 MIE UE WDH ohci_hcd 0000:00:0c.1: hcca frame #04f0 ohci_hcd 0000:00:0c.1: roothub.a 01000201 POTPGT=1 NPS NDP=1 ohci_hcd 0000:00:0c.1: roothub.b 00000000 PPCM=0000 DR=0000 ohci_hcd 0000:00:0c.1: roothub.status 00000000 ohci_hcd 0000:00:0c.1: roothub.portstatus [0] 0x00000100 PPS orinoco.c 0.13e (David Gibson <hermes@gibson.dropbear.id.au> and others) orinoco_pci.c 0.13e (David Gibson <hermes@gibson.dropbear.id.au> & Jean Tourrilhes <jt@hpl.hp.com>) PCI: Enabling device 0000:00:0b.0 (0010 -> 0012) Detected Orinoco/Prism2 PCI device at 0000:00:0b.0, mem:0xF4104000 to 0xF4104FFF -> 0xcf886000, irq:4 Reset done................................................................................................................................................................................................................................; Clear Reset.........................................................................................................................................................................................................................................................................................................................................................................................................................................; pci_cor : reg = 0x0 - FFFBCFD1 - FFFBCDDD eth1: Station identity 001f:0003:0001:0004 eth1: Looks like an Intersil firmware version 1.4.3 eth1: Ad-hoc demo mode supported eth1: IEEE standard IBSS ad-hoc mode supported eth1: WEP supported, 104-bit key eth1: MAC address 00:02:8A:79:F1:14 eth1: Station name "Prism I" eth1: ready kjournald starting. Commit interval 30 seconds EXT3 FS on hda5, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 30 seconds EXT3 FS on hda6, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 30 seconds EXT3 FS on hda7, internal journal EXT3-fs: mounted filesystem with ordered data mode. Linux Kernel Card Services options: [pci] [cardbus] [pm] Yenta: CardBus bridge found at 0000:00:05.0 [13bd:102b] Yenta: ISA IRQ list 0888, PCI irq10 Socket status: 30000006 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
| |