Messages in this thread | | | Date | Thu, 04 Jul 2002 02:17:57 +0800 | From | Nick Urbanik <> | Subject | CMD649 on SMP 2.4.19-pre10-ac2: still not working: please help |
| |
Dear team,
I still have never had our cheap CMD 649 IDE controller cards work on SMP systems, never any problem with single CPU systems. I would really appreciate some help to determine what I can do to get them working. I have 3 SCSI disks, 2 IDE, 1 a slave on ide1 (working), the other a master on ide2 (not working),
The IDE controller isn't getting an interrupt allocated. What can I do to make sure it is? Notice the line in the dmesg output: ide2: DISABLED, NO IRQ
$ lspi 00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4) 00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] 00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 22) 00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 10) 00:07.2 USB Controller: VIA Technologies, Inc. USB (rev 10) 00:07.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30) 00:08.0 RAID bus controller: CMD Technology Inc PCI0649 (rev 02) 00:0a.0 Ethernet controller: National Semiconductor Corporation DP83820 10/100/1000 Ethernet Controller 00:0d.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08) 00:0f.0 SCSI storage controller: Adaptec AIC-7899P U160/m (rev 01) 00:0f.1 SCSI storage controller: Adaptec AIC-7899P U160/m (rev 01) 01:00.0 VGA compatible controller: ATI Technologies Inc Rage XL AGP 2X (rev 65)
part of dmesg output:
Calibrating delay loop... 1736.70 BogoMIPS CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000 Intel machine check reporting enabled on CPU#1. CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 CPU: Common caps: 0383fbff 00000000 00000000 00000000 CPU1: Intel Pentium III (Coppermine) stepping 06 Total of 2 processors activated (3466.85 BogoMIPS). ENABLING IO-APIC IRQs Setting 2 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 2 ... ok. init IO_APIC IRQs IO-APIC (apicid-pin) 2-0, 2-20, 2-21, 2-22, 2-23 not connected. ..TIMER: vector=0x31 pin1=2 pin2=0 number of MP IRQ sources: 23. number of IO-APIC #2 registers: 24. testing the IO APIC.......................
IO APIC #2...... .... register #00: 02000000 ....... : physical APIC id: 02 .... register #01: 00170011 ....... : max redirection entries: 0017 ....... : PRQ implemented: 0 ....... : IO APIC version: 0011 .... register #02: 00000000 ....... : arbitration: 00 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 003 03 0 0 0 0 0 1 1 39 02 003 03 0 0 0 0 0 1 1 31 03 003 03 0 0 0 0 0 1 1 41 04 003 03 0 0 0 0 0 1 1 49 05 003 03 1 1 0 1 0 1 1 51 06 003 03 0 0 0 0 0 1 1 59 07 003 03 0 0 0 0 0 1 1 61 08 003 03 0 0 0 0 0 1 1 69 09 003 03 1 1 0 1 0 1 1 71 0a 003 03 1 1 0 1 0 1 1 79 0b 003 03 1 1 0 1 0 1 1 81 0c 003 03 0 0 0 0 0 1 1 89 0d 003 03 0 0 0 0 0 1 1 91 0e 003 03 0 0 0 0 0 1 1 99 0f 003 03 0 0 0 0 0 1 1 A1 10 003 03 1 1 0 1 0 1 1 A9 11 003 03 1 1 0 1 0 1 1 B1 12 003 03 1 1 0 1 0 1 1 B9 13 003 03 1 1 0 1 0 1 1 C1 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 000 00 1 0 0 0 0 0 0 00 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ10 -> 0:10 IRQ11 -> 0:11 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 IRQ16 -> 0:16 IRQ17 -> 0:17 IRQ18 -> 0:18 IRQ19 -> 0:19 .................................... done. Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 869.8836 MHz. ..... host bus clock speed is 133.8280 MHz. cpu: 0, clocks: 1338280, slice: 446093 CPU0<T0:1338272,T1:892176,D:3,S:446093,C:1338280> cpu: 1, clocks: 1338280, slice: 446093 CPU1<T0:1338272,T1:446080,D:6,S:446093,C:1338280> checking TSC synchronization across CPUs: passed. migration_task 0 on cpu=0 migration_task 1 on cpu=1 PCI: PCI BIOS revision 2.10 entry at 0xf0220, last bus=1 PCI: Using configuration type 1 PCI: Probing PCI hardware Unknown bridge resource 2: assuming transparent PCI: Using IRQ router VIA [1106/0686] at 00:07.0 PCI->APIC IRQ transform: (B0,I7,P3) -> 19 PCI->APIC IRQ transform: (B0,I8,P0) -> 16 PCI->APIC IRQ transform: (B0,I10,P0) -> 18 PCI->APIC IRQ transform: (B0,I13,P0) -> 18 PCI->APIC IRQ transform: (B0,I15,P0) -> 19 PCI->APIC IRQ transform: (B0,I15,P1) -> 19 PCI->APIC IRQ transform: (B1,I0,P0) -> 17 PCI: Enabling Via external APIC routing PCI: Via IRQ fixup for 00:07.2, from 5 to 3 isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found PnPBIOS: Found PnP BIOS installation structure at 0xc00f6210 PnPBIOS: PnP BIOS version 1.0, entry 0xf75a0:0x0, dseg 0xf0000 PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver
another part of dmesg output:
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller on PCI bus 00 dev 39 VP_IDE: chipset revision 16 VP_IDE: not 100% native mode: will probe irqs later ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci00:07.1 ide0: BM-DMA at 0x98c0-0x98c7, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0x98c8-0x98cf, BIOS settings: hdc:DMA, hdd:DMA CMD649: IDE controller on PCI bus 00 dev 40 CMD649: chipset revision 2 CMD649: not 100% native mode: will probe irqs later CMD649: ROM enabled at 0x82100000 ide2: BM-DMA at 0x8400-0x8407, BIOS settings: hde:pio, hdf:pio ide3: BM-DMA at 0x8408-0x840f, BIOS settings: hdg:pio, hdh:pio hda: ATAPI CD-ROM DRIVE 50X MAXIMUM, ATAPI CD/DVD-ROM drive hdc: ST360021A, ATA DISK drive hde: ST320420A, ATA DISK drive hde: IRQ probe failed (0xfffffef8) hdf: IRQ probe failed (0xfffffef8) hdf: IRQ probe failed (0xfffffef8) ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 ide2: DISABLED, NO IRQ ^^^^^^^^^^^^^^^^^^^^____________Oh dear!!!! hdc: host protected area => 1 hdc: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=116301/16/63, UDMA(33) ide-floppy driver 0.99.newide Partition check: hdc: hdc1 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize ide-floppy driver 0.99.newide SCSI subsystem driver Revision: 1.00 kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2 md: raid1 personality registered as nr 3 md: raid5 personality registered as nr 4 raid5: measuring checksumming speed 8regs : 1603.600 MB/sec 32regs : 782.000 MB/sec pIII_sse : 1782.000 MB/sec pII_mmx : 1955.200 MB/sec p5_mmx : 1721.600 MB/sec raid5: using function: pIII_sse (1782.000 MB/sec) md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. LVM version 1.0.3(19/02/2002)
$ cat /proc/interrupts CPU0 CPU1 0: 1815773 1787348 IO-APIC-edge timer 1: 1274 944 IO-APIC-edge keyboard 2: 0 0 XT-PIC cascade 8: 1 0 IO-APIC-edge rtc 12: 45 152 IO-APIC-edge PS/2 Mouse 14: 1 21 IO-APIC-edge ide0 15: 18156 16725 IO-APIC-edge ide1 18: 249413 250012 IO-APIC-level eth0, eth1 19: 76815 76806 IO-APIC-level aic7xxx, aic7xxx, usb-uhci NMI: 0 0 LOC: 3602881 3602880 ERR: 0 MIS: 0
$ cat /proc/ide/cmd64x
Controller: 0 CMD649 Chipset. --------------- Primary Channel ---------------- Secondary Channel -------------
enabled enabled --------------- drive0 --------- drive1 -------- drive0 ---------- drive1 ------
DMA enabled: no no no no DMA Mode: PIO(?) PIO(?) PIO(?) PIO(?) PIO Mode: ? ? ? ? polling polling pending clear enabled enabled
$ cat /proc/ide/via ----------VIA BusMastering IDE Configuration---------------- Driver Version: 3.34 South Bridge: VIA vt82c686a Revision: ISA 0x22 IDE 0x10 Highest DMA rate: UDMA66 BM-DMA base: 0x98c0 PCI clock: 33.3MHz Master Read Cycle IRDY: 1ws Master Write Cycle IRDY: 1ws BM IDE Status Register Read Retry: yes Max DRDY Pulse Width: No limit -----------------------Primary IDE-------Secondary IDE------ Read DMA FIFO flush: yes yes End Sector FIFO flush: no no Prefetch Buffer: no no Post Write Buffer: no no Enabled: yes yes Simplex only: no no Cable Type: 40w 40w -------------------drive0----drive1----drive2----drive3----- Transfer Mode: PIO DMA UDMA DMA Address Setup: 30ns 120ns 30ns 120ns Cmd Active: 90ns 90ns 90ns 90ns Cmd Recovery: 30ns 30ns 30ns 30ns Data Active: 90ns 330ns 90ns 330ns Data Recovery: 30ns 270ns 30ns 270ns Cycle Time: 120ns 600ns 60ns 600ns Transfer Rate: 16.6MB/s 3.3MB/s 33.3MB/s 3.3MB/s
Please could you give me any pointers on how to enable interrupt support for the CMD649 card(s) on this system (and similar systems)? I am sorry, but it's not at all clear to me what to try next.
Yours with hair missing from worry at 2.17am, Nick.
-- Nick Urbanik RHCE nicku@vtc.edu.hk Dept. of Information & Communications Technology Hong Kong Institute of Vocational Education (Tsing Yi) Tel: (852) 2436 8576, (852) 2436 8579 Fax: (852) 2436 8526 PGP: 53 B6 6D 73 52 EE 1F EE EC F8 21 98 45 1C 23 7B ID: 7529555D GPG: 7FFA CDC7 5A77 0558 DC7A 790A 16DF EC5B BB9D 2C24 ID: BB9D2C24
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |