Messages in this thread | | | Date | Thu, 23 May 2002 17:58:51 +0400 | From | "Gryaznova E." <> | Subject | IDE problem: linux-2.5.17 |
| |
Hello.
Kernel starting from 2.5.8 can not boot my Suse 6.4. Booting on those kernels (tested 2.5.8, 2.5.9 and 2.5.17) I am always getting
{ dma_intr } hda: dma_intr: error=0x84 { DriveStatusError BadCRC } hda: recalibrating!
and system either hangs or falls into endless loop.
Kernel 2.5.7 boots and works just fine. The boot log containing information about hardware is attached.
Badblock does not see any bad blocks.
Thanks for any clue on the problem. Lena.
Linux version 2.5.7 (grev@silver) (gcc version 2.95.2 19991024 (release)) #1 SMP Fri Mar 29 16:20:45 MSK 2002 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000000fff0000 (usable) BIOS-e820: 000000000fff0000 - 000000000fff3000 (ACPI NVS) BIOS-e820: 000000000fff3000 - 0000000010000000 (ACPI data) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 255MB LOWMEM available. On node 0 totalpages: 65520 zone(0): 4096 pages. zone(1): 61424 pages. zone(2): 0 pages. Kernel command line: auto BOOT_IMAGE=2.5.7 ro root=306 vga=0x0301 Local APIC disabled by BIOS -- reenabling. Found and enabled local APIC! Initializing CPU#0 Detected 698.666 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 1392.64 BogoMIPS Memory: 256464k/262080k available (1241k kernel code, 5232k reserved, 430k data, 208k init, 0k highmem) Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes) Inode-cache hash table entries: 16384 (order: 5, 131072 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes) Page-cache hash table entries: 65536 (order: 6, 262144 bytes) CPU: Before vendor init, caps: 0183fbff c1c3fbff 00000000, vendor = 2 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: After vendor init, caps: 0183fbff c1c3fbff 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: 0183fbff c1c3fbff 00000000 00000000 CPU: Common caps: 0183fbff c1c3fbff 00000000 00000000 Enabling fast FPU save and restore... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX CPU: Before vendor init, caps: 0183fbff c1c3fbff 00000000, vendor = 2 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: After vendor init, caps: 0183fbff c1c3fbff 00000000 00000000 Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: 0183fbff c1c3fbff 00000000 00000000 CPU: Common caps: 0183fbff c1c3fbff 00000000 00000000 WARNING: This combination of AMD processors is not suitable for SMP. CPU0: AMD Athlon(tm) Processor stepping 01 per-CPU timeslice cutoff: 1463.62 usecs. task migration cache decay timeout: 10 msecs. SMP motherboard not detected. enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 698.6489 MHz. ..... host bus clock speed is 199.6139 MHz. cpu: 0, clocks: 1996139, slice: 998069 CPU0<T0:1996128,T1:998048,D:11,S:998069,C:1996139> Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket PCI: PCI BIOS revision 2.10 entry at 0xfb430, last bus=1 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) Starting kswapd BIO: pool of 256 setup, 14Kb (56 bytes/bio) biovec: init pool 0, 1 entries, 12 bytes biovec: init pool 1, 4 entries, 48 bytes biovec: init pool 2, 16 entries, 192 bytes biovec: init pool 3, 64 entries, 768 bytes biovec: init pool 4, 128 entries, 1536 bytes biovec: init pool 5, 256 entries, 3072 bytes VFS: Diskquotas version dquot_6.4.0 initialized Detected PS/2 Mouse Port. pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A block: 256 slots per queue, batch=32 Intel(R) PRO/100 Fast Ethernet Adapter - Loadable driver, ver 2.0.24-pre1 Copyright (c) 2002 Intel Corporation
eth0: Intel(R) PRO/100+ Management Adapter Mem:0xe5101000 IRQ:11 Speed:100 Mbps Dx:Full Hardware receive checksums enabled cpu cycle saver enabled
[drm] Initialized tdfx 1.0.0 20010216 on minor 0 Uniform Multi-Platform E-IDE driver ver.:7.0.0 ide: system bus speed 33MHz Advanced Micro Devices [AMD] AMD-756 [Viper] IDE: IDE controller on PCI slot 00:07.1 Advanced Micro Devices [AMD] AMD-756 [Viper] IDE: chipset revision 3 Advanced Micro Devices [AMD] AMD-756 [Viper] IDE: not 100% native mode: will probe irqs later AMD_IDE: Advanced Micro Devices [AMD] AMD-756 [Viper] IDE (rev 03) UDMA66 controller on pci00:07.1 ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio hda: IBM-DJNA-371800, ATA DISK drive hdc: SONY CDU4811, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 blk: queue c033dd0c, I/O limit 4095Mb (mask 0xffffffff) hda: 35239680 sectors (18043 MB) w/1966KiB Cache, CHS=34960/16/63, (U)DMA Partition check: hda: [PTBL] [2193/255/63] hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 > Advanced Linux Sound Architecture Driver Version 0.9.0beta12 (Mon Mar 18 15:44:40 2002 UTC). kmod: failed to exec /sbin/modprobe -s -k snd-card-0, errno = 2 ALSA device list: No soundcards found. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 1024 buckets, 16Kbytes TCP: Hash tables configured (established 8192 bind 10922) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 208k freed hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } hda: dma_intr: error=0x84 { DriveStatusError BadCRC } hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } hda: dma_intr: error=0x84 { DriveStatusError BadCRC } hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } hda: dma_intr: error=0x84 { DriveStatusError BadCRC } hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } hda: dma_intr: error=0x84 { DriveStatusError BadCRC } ide0: reset: success Adding Swap: 136544k swap-space (priority -1)
| |