Messages in this thread | | | From | Saleh Jamil <> | Subject | Need help with sb1000 and ker.2.2.11 | Date | Tue, 24 Aug 1999 20:45:35 -0500 |
| |
Hello,
I can't get my general instruments sb1000 cable modem working after compiling kernel 2.2.11. Afterwards I went to Clemmit Sigler's sb1000 web page, and then I patched the 2.2.11 kernel and recompiled it. Still, I can't connect to my ISP (Adelphia). This is the output of what I get when starting the sb1000 under kernel 2.2.7:
Aug 24 19:05:20 TheFray kernel: PPP: version 2.3.7 (demand dialling) Aug 24 19:05:20 TheFray kernel: PPP line discipline registered. Aug 24 19:05:20 TheFray kernel: registered device ppp0 Aug 24 19:05:20 TheFray pppd[381]: pppd 2.3.8 started by root, uid 0
<snipped chat script output>
Aug 24 19:05:39 TheFray pppd[381]: Serial connection established. Aug 24 19:05:39 TheFray pppd[381]: Using interface ppp0 Aug 24 19:05:39 TheFray pppd[381]: Connect: ppp0 <--> /dev/ttyS0 Aug 24 19:05:46 TheFray pppd[381]: Remote message: ^D^EM-j^B^F Aug 24 19:05:46 TheFray kernel: PPP BSD Compression module registered Aug 24 19:05:46 TheFray kernel: PPP Deflate Compression module registered Aug 24 19:05:48 TheFray pppd[381]: local IP address 24.48.36.233 Aug 24 19:05:48 TheFray pppd[381]: remote IP address 10.1.65.141 Aug 24 19:05:48 TheFray kernel: cm0: sb1000 at (0x120,0x310), csn 1, S/N 0x25e58c87, IRQ 5. Aug 24 19:05:48 TheFray kernel: sb1000.c:v1.1.2 6/01/98 (fventuri@mediaone.net)
cm0 Link encap:Ethernet HWaddr 00:00:25:E5:8C:87 inet addr:24.48.36.233 P-t-P:10.1.65.141 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 Interrupt:5 Base address:0x120
lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:3924 Metric:1 RX packets:297 errors:0 dropped:0 overruns:0 frame:0 TX packets:297 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0
ppp0 Link encap:Point-to-Point Protocol inet addr:24.48.36.233 P-t-P:10.1.65.141 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1514 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:9 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10
Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.1.65.141 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 10.1.65.141 0.0.0.0 255.255.255.255 UH 0 0 0 cm0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 10.1.65.141 0.0.0.0 UG 0 0 0 ppp0
And here is what I get when connecting under kernel 2.2.11 with ppp and the patched sb1000 driver compiled:
Aug 24 19:12:58 shaybah modprobe: modprobe: Can't locate module ppp0 Aug 24 19:12:58 shaybah kernel: registered device ppp0 Aug 24 19:12:58 shaybah pppd[286]: pppd 2.3.8 started by root, uid 0
<snipped chat script output>
Aug 24 19:18:25 shaybah pppd[286]: Serial connection established. Aug 24 19:18:25 shaybah pppd[286]: Using interface ppp0 Aug 24 19:18:25 shaybah pppd[286]: Connect: ppp0 <--> /dev/ttyS0 Aug 24 19:18:25 shaybah chat[313]: CONNECT Aug 24 19:18:25 shaybah chat[313]: -- got it Aug 24 19:18:29 shaybah pppd[286]: Remote message: ^D^EM-j^B^F Aug 24 19:18:30 shaybah pppd[286]: local IP address 24.48.37.39 Aug 24 19:18:30 shaybah pppd[286]: remote IP address 10.1.65.141 Aug 24 19:18:30 shaybah kernel: cm0: sb1000 at (0x110,0x310), csn 1, S/N 0x25e58c87, IRQ 5. Aug 24 19:18:30 shaybah kernel: sb1000.c:v1.1.2 6/01/98 (fventuri@mediaone.net)
cm0 Link encap:Ethernet HWaddr 00:00:25:E5:8C:87 unspec addr:[NONE SET] P-t-P:[NONE SET] Mask:[NONE SET] UP POINTOPOINT RUNNING NOARP MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 Interrupt:5 Base address:0x110
lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:3924 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0
ppp0 Link encap:Point-to-Point Protocol inet addr:24.48.37.39 P-t-P:10.1.65.141 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1514 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:9 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10
Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.1.65.141 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 10.1.65.141 0.0.0.0 UG 0 0 0 ppp0
Now in pre-2.2.11 kernels, all I did was run Clemmit's sb1000 auto-install script, and everything worked fine. Should I re-run the auto-install script after compiling the newer kernel? Should I compile cmconfig.c alone?
Any help would be greatly appreciated.
Saleh
----------------------------------------------------------------------- Saleh Jamil SJamil@Adelphia.Net
Absorb what is useful, discard what is useless....but most importantly change what needs to be changed so that things work better. ------------------------------------------------------------------------
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.rutgers.edu Please read the FAQ at http://www.tux.org/lkml/
| |