Messages in this thread | | | Date | Wed, 10 Nov 1999 11:54:08 -0500 (EST) | From | Andrew Burke <> | Subject | 2.3.x and signal 10 w/ fsck.ext2... |
| |
After trying kernels 2.3.22, 2.3.23 and 2.3.26 i finally got my system to come all the way up by forcing fsck to check my drives serially...
Before this I was getting signal 10 (operational error, reboot) on /dev/hda7. However, if i went into single user mode and fsck -f'd it, it was fine, no errors. So i was wondering if anyone else had had this problem, if it was a known issues, if it's some weird special case, etc...
i realize that fdisk complains about partition 1 nore ending on a cylinder boundry, however, the drive is 14 gigs, and i assume that fdisk is simply confused... it's worked perfectly under 2.2.x and now seems to be fine under 2.3.26 after i do non-parrallel fsck... obviously, being hda, it's an IDE drive... it's an IBM 14GXP 14gb 7200 rpm drive.
I also included the info on my second drive (/home) just in case someone felt it might have an impact. It's one huge paritition, but nothing seems to complain about it.
info follows:
[jane]:~/uname -a Linux jane 2.3.26 #6 Wed Nov 10 01:07:45 EST 1999 i686 unknown
Command (m for help): p
Disk /dev/hda: 255 heads, 63 sectors, 1757 cylinders Units = cylinders of 16065 * 512 bytes
Device Boot Start End Blocks Id System /dev/hda1 * 1 879 7060536 b Win95 FAT32 Partition 1 does not end on cylinder boundary: phys=(1023, 15, 63) should be (1023, 254, 63) /dev/hda2 * 880 896 136552+ 83 Linux /dev/hda3 897 1757 6915982+ 5 Extended /dev/hda5 897 1027 1052226 83 Linux /dev/hda6 1028 1158 1052226 83 Linux /dev/hda7 1159 1723 4538331 83 Linux /dev/hda8 1724 1740 136521 82 Linux swap /dev/hda9 1741 1757 136521 82 Linux swap
Command (m for help): p
Disk /dev/hdd: 16 heads, 63 sectors, 32760 cylinders Units = cylinders of 1008 * 512 bytes
Device Boot Start End Blocks Id System /dev/hdd1 1 32760 16511008+ 83 Linux
ps. does anyone know if there are known issues with USB mice being "unresponsive" in 2.3.x? My mouse seems sluggish, doesn't pick up clicks as nicely as the ps/2, etc... any info would be appreciated, and any pointers would be helpful...
also, does anyone know the equivalent for this under 2.3.x?:
ioaddr = pcidev->base_address[0];
i looked around for a while, and all i could find that seems to make any sense is something like:
ioaddr = pcidev->resource[0].start;
but this is not working, and i haven't taken the time to really look at a lot of this, and wondered if someone here might be able to give me the quick fix... this code is from the sblive driver (emu10k1)... i got it to build, but I get "Device or resource busy"... i'm assuming that's because i'm ending up w/ the wrong base address... otherwise, i think i might be semi-close to having it working... but then again, i'm not too familiar w/ drivers, so i could be way off-base...
thanks in advance...
andy
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.rutgers.edu Please read the FAQ at http://www.tux.org/lkml/
| |