lkml.org 
[lkml]   [1997]   [May]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Subject2.1.40 failed to boot.
Date
Just tried the 2.1.40 kernel on a Compaq Systempro (386DX+387)
and it crashes right after two lines of (taken from memory):

hda: CPQ001373 Drive Array Controller, ATA
hdb: CPQ001373 Drive Array Controller, ATA
with endless printouts of:
Interrupt lock in context c010ac49
Interrupt lock in context c010ac49
Interrupt lock in context c010ac49
...
Where c010ac49 is:
c010ac30 T math_error
c010acf8 T do_coprocessor_error
---
It works in 2.0.30, and I provide dmesg output for 2.0.30 below:

klogd 1.3-3, log source = /proc/kmsg started.
Cannot find map file.
Loaded 45 symbols from 3 modules.
Console: 16 point font, 400 scans
Console: colour VGA+ 80x25, 1 virtual console (max 63)
Calibrating delay loop.. ok - 6.60 BogoMIPS
Memory: 14792k/16256k available (580k kernel code, 384k reserved, 500k data)
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.13 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: ICMP, UDP, TCP
Checking 386/387 coupling... Ok, fpu using old IRQ13 error reporting
Checking 'hlt' instruction... Ok.
Linux version 2.0.30 (root@flash.uucp.dtek.chalmers.se) (gcc version 2.7.2.1) #3 Fri Apr 11 01

hda: CPQ001373 Drive Array Controller, 810MB w/128kB Cache, CHS=823/32/63
hdb: CPQ001373 Drive Array Controller, 405MB w/128kB Cache, CHS=823/16/63
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Floppy drive(s): fd0 is 1.44M
Started kswapd v 1.4.2.2
FDC 0 is a pre-1991 82077
md driver 0.35 MAX_MD_DEV=4, MAX_REAL=8
aic7xxx: Chip reset not cleared; clearing manually.
aic7xxx: Extended translation disabled.
aic7xxx: AHA-2740 Rev C and previous.
aic7xxx: Memory check yields 4 SCBs, paging not enabled.
aic7xxx: Using edge triggered interrupts.
aic7xxx: Enabled channel B of AHA-2740-Twin.
AHA-2740-TWIN AT EISA SLOT 5:
irq 15
bus release time 12 bclks
data fifo threshold 100
SCSI CHANNEL A:
scsi id 7
scsi selection timeout 64 ms
scsi bus reset at power-on enabled
scsi bus parity enabled
scsi bus termination (low byte) disabled
aic7xxx: Downloading sequencer code...done.
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 4.0/3.2/4.0
scsi : 1 host.
scsi0: Scanning channel A for devices.
scsi0: Target 1, channel A, now synchronous at 10.0MHz, offset 15.
Vendor: CONNER Model: CFP1060S 1.05GB Rev: 203C
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 1, lun 0
scsi0: Target 2, channel A, now synchronous at 10.0MHz, offset 15.
Vendor: SEAGATE Model: ST11900N Rev: 9700
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 2, lun 0
scsi0: Scanning channel B for devices.
scsi0: Target 2, channel B, now synchronous at 5.0MHz, offset 15.
Vendor: ARCHIVE Model: Python 25947-XXX Rev: 2.49
Type: Sequential-Access ANSI SCSI revision: 02
scsi : detected 2 SCSI disks total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 2074880 [1013 MB] [1.0 GB]
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 3310215 [1616 MB] [1.6 GB]
Ethernet Bridge 002 for NET3.035 (Linux 2.0)
eth0: 3c509 at 0x6000 tag 0, AUI port, address 00 20 af 73 e1 a1, IRQ 5.
3c509.c:1.07 6/15/95 becker@cesdis.gsfc.nasa.gov
Partition check:
sda: sda1 < sda5 sda6 sda7 > sda2
sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb7 sdb8
hda: hda1 < hda5 hda6 > hda2 hda3
hdb: hdb1 < hdb5 >
VFS: Mounted root (ext2 filesystem) readonly.
Adding Swap: 41964k swap-space (priority -1)
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Detected scsi tape st0 at scsi0, channel 1, id 2, lun 0

--

Fredrik Lundholm
exce7@ce.chalmers.se

\
 
 \ /
  Last update: 2005-03-22 13:39    [W:0.023 / U:0.008 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site